ATSAM3S4CA-AU Atmel, ATSAM3S4CA-AU Datasheet - Page 428

• Manufacturer Part Number: ATSAM3S4CA-AU
• Description: IC MCU 32BIT 256KB FLASH 100LQFP
• Manufacturer: Atmel
• Series: SAM3Sr

Specifications of ATSAM3S4CA-AU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 79
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 1.95 V
• Data Converters: A/D 16x10/12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Controller Family/series: ATSAM3S
• No. Of I/o's: 79
• Ram Memory Size: 48KB
• Cpu Speed: 64MHz
• No. Of Timers: 6
• Rohs Compliant: Yes
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3S-EK
• Cpu Family: AT91
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 64MHz
• Total Internal Ram Size: 48KB
• # I/os (max): 79
• Number Of Timers - General Purpose: 6
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.62V
• On-chip Adc: 16-chx12-bit
• On-chip Dac: 2-chx12-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

428
SAM3S Preliminary
(MUL + 1)/DIV. When MUL is written to 0, the PLL is disabled and its power consumption is
saved. Re-enabling the PLL can be performed by writing a value higher than 0 in the MUL field.
Whenever the PLL is re-enabled or one of its parameters is changed, the LOCK (LOCKA,
LOCKB) bit in PMC_SR is automatically cleared. The values written in the PLLCOUNT field
(PLLACOUNT, PLLBCOUUNT) in CKGR_PLLR (CKGR_PLLAR, CKGR_PLLBR) are loaded in
the PLL counter. The PLL counter then decrements at the speed of the Slow Clock until it
reaches 0. At this time, the LOCK bit is set in PMC_SR and can trigger an interrupt to the pro-
cessor. The user has to load the number of Slow Clock cycles required to cover the PLL
transient time into the PLLCOUNT field.
The PLL clock can be divided by 2 by writing the PLLDIV2 (PLLADIV2, PLLBDIV2) bit in
PMC_MCKR register.
It is forbidden to change 4/8/12 MHz Fast RC oscillator, or main selection in CKGR_MOR regis-
ter while Master clock source is PLL and PLL reference clock is the Fast RC oscillator.
The user must:
• Switch on the Main RC oscillator by writing 1 in CSS field of PMC_MCKR.
• Change the frequency (MOSCRCF) or oscillator selection (MOSCSEL) in CKGR_MOR.
• Wait for MOSCRCS (if frequency changes) or MOSCSELS (if oscillator selection changes) in
• Disable and then enable the PLL (LOCK in PMC_IDR and PMC_IER register).
• Wait for PLLRDY.
• Switch back to PLL.
PMC_IER.
6500C–ATARM–8-Feb-11