ATSAM3S4CA-AU Atmel, ATSAM3S4CA-AU Datasheet - Page 928

• Manufacturer Part Number: ATSAM3S4CA-AU
• Description: IC MCU 32BIT 256KB FLASH 100LQFP
• Manufacturer: Atmel
• Series: SAM3Sr

Specifications of ATSAM3S4CA-AU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 79
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 1.95 V
• Data Converters: A/D 16x10/12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Controller Family/series: ATSAM3S
• No. Of I/o's: 79
• Ram Memory Size: 48KB
• Cpu Speed: 64MHz
• No. Of Timers: 6
• Rohs Compliant: Yes
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3S-EK
• Cpu Family: AT91
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 64MHz
• Total Internal Ram Size: 48KB
• # I/os (max): 79
• Number Of Timers - General Purpose: 6
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.62V
• On-chip Adc: 16-chx12-bit
• On-chip Dac: 2-chx12-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

37.5
37.5.1
37.5.2
928
Typical Connection
SAM3S Preliminary
USB Device Transceiver
VBUS Monitoring
Figure 37-2. Board Schematic to Interface Device Peripheral
The USB device transceiver is embedded in the product. A few discrete components are
required as follows:
VBUS monitoring is required to detect host connection. VBUS monitoring is done using a stan-
dard PIO with internal pull-up disabled. When the host is switched off, it should be considered as
a disconnect, the pull-up must be disabled in order to prevent powering the host through the pull-
up resistor.
When the host is disconnected and the transceiver is enabled, then DDP and DDM are floating.
This may lead to over consumption. A solution is to enable the integrated pull-down by disabling
the transceiver (TXVDIS = 1) and then remove the pull-up (PUON = 0).
A termination serial resistor must be connected to DDP and DDM. The resistor value is defined
in the electrical specification of the product (R
• the application detects all device states as defined in chapter 9 of the USB specification;
• to reduce power consumption the host is disconnected
• for line termination.
PIO
DDM
DDP
– VBUS monitoring
5V Bus Monitoring
47 K
27 K
R
R
EXT
EXT
EXT
).
2
3
Connector
6500C–ATARM–8-Feb-11
Type B
1
4