ATMEGA128-16MN Atmel, ATMEGA128-16MN Datasheet - Page 54

• Manufacturer Part Number: ATMEGA128-16MN
• Description: MCU AVR 128KB FLASH 16MHZ 64QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA128-16MN

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-MLF®, 64-QFN
• Processor Series: ATMEGA128x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK501 - ADAPTER KIT FOR 64PIN AVR MCUATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Voltage Reference
Enable Signals and
Start-up Time
Watchdog Timer
54
ATmega128
The voltage reference has a start-up time that may influence the way it should be used. The
start-up time is given in
erence is on during the following situations:
1. When the BOD is enabled (by programming the BODEN fuse).
2. When the bandgap reference is connected to the Analog Comparator (by setting the
3. When the ADC is enabled.
Thus, when the BOD is not enabled, after setting the ACBG bit or enabling the ADC, the user
must always allow the reference to start up before the output from the Analog Comparator or
ADC is used. To reduce power consumption in Power-down mode, the user can avoid the three
conditions above to ensure that the reference is turned off before entering Power-down mode.
Table 20. Internal Voltage Reference Characteristics
The Watchdog Timer is clocked from a separate On-chip Oscillator which runs at 1MHz. This is
the typical value at V
controlling the Watchdog Timer prescaler, the Watchdog Reset interval can be adjusted as
shown in
Timer. The Watchdog Timer is also reset when it is disabled and when a Chip Reset occurs.
Eight different clock cycle periods can be selected to determine the reset period. If the reset
period expires without another Watchdog Reset, the ATmega128 resets and executes from the
Reset Vector. For timing details on the Watchdog Reset, refer to
To prevent unintentional disabling of the Watchdog or unintentional change of time-out period, 3
different safety levels are selected by the Fuses M103C and WDTON as shown in Table 21.
Safety level 0 corresponds to the setting in ATmega103. There is no restriction on enabling the
WDT in any of the safety levels. Refer to
the Watchdog Timer” on page 57
Symbol
ACBG bit in ACSR).
V
t
I
BG
BG
BG
Table 22 on page
Parameter
Bandgap reference voltage
Bandgap reference start-up time
Bandgap reference current consumption
CC
Table
= 5V. See characterization data for typical values at other V
56. The WDR – Watchdog Reset – instruction resets the Watchdog
20. To save power, the reference is not always turned on. The ref-
for details.
“Timed Sequences for Changing the Configuration of
1.15
Min
1.23
Typ
page
40
10
53.
Max
1.40
70
Units
µA
µs
2467V–AVR–02/11
V
CC
levels. By