AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 647

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

26.7.3.6
26.7.3.7
32072G–11/2011
Pipe activation
Address setup
The pipe is maintained inactive and reset (see
disabled (PENn is zero). The Data Toggle Sequence field (DTSEQ) is also reset.
The algorithm represented on
pipe.
Figure 26-23. Pipe Activation Algorithm
As long as the pipe is not correctly configured (UPSTAn.CFGOK is zero), the controller can not
send packets to the device through this pipe.
The UPSTAn.CFGOK bit is set only if the configured size and number of banks are correct com-
pared to their maximal allowed values for the pipe (see
maximal FIFO size (i.e. the DPRAM size).
See
Once the pipe is correctly configured (UPSTAn.CFGOK is zero), only the PTOKEN and INTFRQ
fields can be written by software. INTFRQ is meaningless for non-interrupt pipes.
When starting an enumeration, the user gets the device descriptor by sending a
GET_DESCRIPTOR USB request. This descriptor contains the maximal packet size of the
device default control endpoint (bMaxPacketSize0) and the user re-configures the size of the
default control pipe with this size parameter.
Once the device has answered the first host requests with the default device address 0, the host
assigns a new address to the device. The host controller has to send an USB reset to the device
and to send a SET_ADDRESS(addr) SETUP request with the new address to be used by the
device. Once this SETUP transaction is over, the user writes the new address into the USB Host
Address for Pipe n field in the USB Host Device Address register (UHADDR.UHADDRPn). All
following requests, on all pipes, will be performed using this new address.
Section 26.7.1.6
Pipe Activated
Yes
CFGOK ==
Activation
PENn = 1
UPCFGn
PEPNUM
PTOKEN
INTFRQ
PTYPE
ALLOC
PSIZE
Pipe
for more details about DPRAM management.
PBK
1?
Figure 26-23 on page 647
No
ERROR
Section 26.7.3.5
Enable the pipe.
Configure the pipe:
Allocate the configured DPRAM banks.
Test if the pipe configuration is
correct.
- interrupt request frequency
- endpoint number
- type
- size
- number of banks
must be followed in order to activate a
Table 26-1 on page
for more details) as long as it is
617) and to the
647