AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 405

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

21.5
21.6
21.6.1
21.6.2
21.6.3
21.7
21.7.1
32072G–11/2011
I/O Lines Description
Product Dependencies
Functional Description
I/O Lines
Clocks
Interrupts
Modes of Operation
Table 21-1.
In order to use this module, other parts of the system must be configured correctly, as described
below.
The pins used for interfacing the compliant external devices may be multiplexed with I/O lines.
The user must first configure the I/O Controller to assign the SPI pins to their peripheral
functions.
The clock for the SPI bus interface (CLK_SPI) is generated by the Power Manager. This clock is
enabled at reset, and can be disabled in the Power Manager. It is recommended to disable the
SPI before disabling the clock, to avoid freezing the SPI in an undefined state.
The SPI interrupt request line is connected to the interrupt controller. Using the SPI interrupt
requires the interrupt controller to be programmed first.
The SPI operates in master mode or in slave mode.
Operation in master mode is configured by writing a one to the Master/Slave Mode bit in the
Mode Register (MR.MSTR). The pins NPCS0 to NPCS3 are all configured as outputs, the SPCK
pin is driven, the MISO line is wired on the receiver input and the MOSI line driven as an output
by the transmitter.
If the MR.MSTR bit is written to zero, the SPI operates in slave mode. The MISO line is driven by
the transmitter output, the MOSI line is wired on the receiver input, the SPCK pin is driven by the
transmitter to synchronize the receiver. The NPCS0 pin becomes an input, and is used as a
Slave Select signal (NSS). The pins NPCS1 to NPCS3 are not driven and can be used for other
purposes.
The data transfers are identically programmable for both modes of operations. The baud rate
generator is activated only in master mode.
Pin Name
MISO
MOSI
SPCK
NPCS1-NPCS3
NPCS0/NSS
I/O Lines Description
Pin Description
Master In Slave Out
Master Out Slave In
Serial Clock
Peripheral Chip Selects
Peripheral Chip Select/Slave Select
Master
Input
Output
Output
Output
Output
Type
Slave
Output
Input
Unused
Input
Input
405