AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 325

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

19.9.1
19.9.1.1
Figure 19-7. Multi-block Transfer Using Linked Lists
32072G–11/2011
Multi-block Transfers
LLPx(0)
Block Chaining Using Linked Lists
CTLx[63..32]
CTLx[31..0]
LLPx(1)
DARx
SARx
A block descriptor (LLI) consists of following registers, SARx, DARx, LLPx, CTL. These regis-
ters, along with the CFGx register, are used by the DMACA to set up and describe the block
transfer.
In this case, the DMACA re-programs the channel registers prior to the start of each block by
fetching the block descriptor for that block from system memory. This is known as an LLI update.
DMACA block chaining is supported by using a Linked List Pointer register (LLPx) that stores the
address in memory of the next linked list item. Each LLI (block descriptor) contains the corre-
sponding block descriptor (SARx, DARx, LLPx, CTLx).
To set up block chaining, a sequence of linked lists must be programmed in memory.
The SARx, DARx, LLPx and CTLx registers are fetched from system memory on an LLI update.
The updated contents of the CTLx register are written back to memory on block completion.
ure 19-7 on page 325
transfers using block chaining.
The Linked List multi-block transfers is initiated by programming LLPx with LLPx(0) (LLI(0) base
address) and CTLx with CTLx.LLP_S_EN and CTLx.LLP_D_EN.
LLI(0)
shows how to use chained linked lists in memory to define multi-block
System Memory
LLPx(1)
CTLx[63..32]
CTLx[31..0]
LLPx(2)
DARx
SARx
LLI(1)
LLPx(2)
Fig-
325