AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 590

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25.7.2
Name:
Access Type:
Offset:
Reset Value:
This register can only be written if the WPEN bit is cleared in the Write Protect Mode Register.
• ONEBIT: Start Frame Delimiter Selector
• MODSYNC: Manchester Synchronization Mode
• MAN: Manchester Encoder/Decoder Enable
• FILTER: Infrared Receive Line Filter
• MAX_ITERATION
• VAR_SYNC: Variable Synchronization of Command/Data Sync Start Frame Delimiter
• DSNACK: Disable Successive NACK
• INACK: Inhibit Non Acknowledge
• OVER: Oversampling Mode
• CLKO: Clock Output Select
32072G–11/2011
ONEBIT
31
23
15
–
7
0: The start frame delimiter is a command or data sync, as defined by MODSYNC.
1: The start frame delimiter is a normal start bit, as defined by MODSYNC.
0: The manchester start bit is either a 0-to-1 transition, or a data sync.
1: The manchester start bit is either a 1-to-0 transition, or a command sync.
0: Manchester endec is disabled.
1: Manchester endec is enabled.
0: The USART does not filter the receive line.
1: The USART filters the receive line by doing three consecutive samples and uses the majority value.
This field determines the number of acceptable consecutive NACK’s when in protocol T=0.
0: Sync pattern according to MODSYNC.
1: Sync pattern according to THR.TXSYNH.
0: NACK’s are handled as normal, unless disabled by INACK.
1: The receiver restricts the amount of consecutive NACK’s by MAX_ITERATION value. If MAX_ITERATION=0 no NACK will be
issued and the first erroneous message is accepted as a valid character, setting CSR.ITER.
0: The NACK is generated.
1: The NACK is not generated.
0: Oversampling at 16 times the baud rate.
1: Oversampling at 8 times the baud rate.
0: The USART does not drive the CLK pin.
1: The USART drives the CLK pin unless USCLKS selects the external clock.
Mode Register
CHMODE
CHRL
VAR_SYNC
MODSYNC
30
22
14
MR
Read-write
0x4
0x00000000
6
DSNACK
MAN
29
21
13
5
NBSTOP
USCLKS
FILTER
INACK
28
20
12
4
OVER
27
19
11
–
3
CLKO
PAR
26
18
10
2
MODE
MAX_ITERATION
MODE9
25
17
9
1
SYNC/CPHA
MSBF/CPOL
24
16
8
0
590