AT32UC3L064_1 ATMEL [ATMEL Corporation], AT32UC3L064_1 Datasheet - Page 614
AT32UC3L064_1
Manufacturer Part Number
AT32UC3L064_1
Description
AVR32 32-bit Microcontroller
Manufacturer
ATMEL [ATMEL Corporation]
Datasheet
1.AT32UC3L064_1.pdf
(825 pages)
- Current page: 614 of 825
- Download datasheet (13Mb)
26.7
26.7.1
26.7.2
32099A–AVR32–06/09
Resisitve Touch Screen
Resistive Touch Screen Principles
Position Measurement Method
The ADCIFB embeds an integrated resistive touch screen sequencer that can be used to calcu-
late contact coordinates on a resistive film touch screen. When instructed to start, the integrated
touch screen sequencer automatically applies a sequence of voltage patterns to the touch
screen films and the Analog-to-Digital Conversion cell is used to measure the effects. The result-
ing measurements can be used to calculate the horizontal and vertical contact coordinates.
The touch screen film is connected to the ADCIFB using the AD and DP pins. See
26.7.3
Touch Screen ADC Mode is enabled by writing a one to the TSAMOD field in the Mode Register
(MR). In this mode, channels TSPO+0 though TSPO+3 are automatically enabled where TSPO
refers to the Touch Screen Pin Offset field in the Mode Register. For each conversion sequence,
all enabled channles before TSPO+0 and after TSPO+3 are converted as ordinary ADC chan-
nels, producing 1 conversion result each. When the sequencer enters the TSPO+0 channel the
touch screen sequencer will take over control and convert the next 4 channles as described in
Section
A resistive touch screen is based on two resistive films, each one fitted with a pair of electrodes,
placed at the top and bottom on one film, and on the right and left on the other. Between the two,
there is a layer that acts as an insulator, but makes a connection when pressure is applied to the
screen. This is illustrated in
Figure 26-2. Touch Screen Position Measurement
As shown in
to X
there is a voltage gradient from top to bottom on the first film. When a contact is performed on
P
(top) and X
for details.
26.7.4.
Figure 26-2 on page
Vertical Position Detection
X
m
X
M
P
(bottom) leaving Y
Y
M
Y
P
Figure 26-2 on page
Volt
VDD
GND
614, to detect the position of a contact, voltage is first applied
X
p
M
and Y
Contact
Pen
m
tristated. Due to the linear resistance of the film,
614.
X
P
Horizontal Position Detection
Y
Y
M
P
Y
P
X
P
AT32UC3L
Volt
VDD
GND
Section
614
Related parts for AT32UC3L064_1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory, 16Kbit
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontrollers
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 16/32/64/128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 16/32/64K Bytes In-System Programmable Programmable
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet: