AT32UC3L064_1 ATMEL [ATMEL Corporation], AT32UC3L064_1 Datasheet - Page 108
AT32UC3L064_1
Manufacturer Part Number
AT32UC3L064_1
Description
AVR32 32-bit Microcontroller
Manufacturer
ATMEL [ATMEL Corporation]
Datasheet
1.AT32UC3L064_1.pdf
(825 pages)
- Current page: 108 of 825
- Download datasheet (13Mb)
10.5.10
10.5.11
10.5.12
10.6
10.6.1
32099A–AVR32–06/09
Performance Monitors
Priority
Error Handling
Peripheral Event Trigger
Measuring mechanisms
If more than one PDCA channel is requesting transfer at a given time, the PDCA channels are
prioritized by their channel number. Channels with lower numbers have priority over channels
with higher numbers, giving channel zero the highest priority.
If the Memory Address Register (MAR) is set to point to an invalid location in memory, an error
will occur when the PDCA tries to perform a transfer. When an error occurs, the Transfer Error
bit in the Interrupt Status Register (ISR.TERR) will be set and the DMA channel that caused the
error will be stopped. In order to restart the channel, the user must program the Memory
Address Register to a valid address and then write a one to the Error Clear bit in the Control
Register (CR.ECLR). If the Transfer Error interrupt is enabled, an interrupt request will be gener-
ated when an transfer error occurs.
Peripheral events can be used to trigger PDCA channel transfers. Peripheral Event synchroniza-
tions are enabled by writing a one to the Event Trigger bit in the Mode Register (MR.ETRIG).
When set, all DMA requests will be blocked until an peripheral event is received. For each
peripheral event received, only one data item is transferred. If no DMA requests are pending
when a peripheral event is received, the PDCA will start a transfer as soon as a peripheral event
is detected. If multiple events arrive while the PDCA channel is busy transferring data, an over-
flow condition will be signaled in the Peripheral Event System. Refer to the Peripheral Event
System chapter for more information.
Two performance monitors allow the user to measure the activity and stall cycles for PDCA
transfers. To monitor a PDCA channel, the corresponding channel number must be written to
one of the MONnCH fields in the Performance Control Register (PCONTROL) and a one must
be written to the corresponding CHnEN bit in the same register.
Due to performance monitor hardware resource sharing, the two monitor channels should NOT
be programmed to monitor the same PDCA channel. This may result in UNDEFINED perfor-
mance monitor behavior.
Three different parameters can be measured by each channel:
These measurements can be extracted by software and used to generate indicators for bus
latency, bus load, and maximum bus latency.
Each of the counters has a fixed width, and may therefore overflow. When an overflow is
encountered in either the Performance Channel Data Read/Write Cycle registers (PRDATAn
and PWDATAn) or the Performance Channel Read/Write Stall Cycles registers (PRSTALLn and
PWSTALLn) of a channel, all registers in the channel are reset. This behavior is altered if the
Channel Overflow Freeze bit is one in the Performance Control register (PCONTROL.CHnOVF).
If this bit is one, the channel registers are frozen when either DATA or STALL reaches its maxi-
mum value. This simplifies one-shot readout of the counter values.
• The number of data transfer cycles since last channel reset, both for read and write
• The number of stall cycles since last channel reset, both for read and write
• The maximum latency since last channel reset, both for read and write
AT32UC3L
108
Related parts for AT32UC3L064_1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory, 16Kbit
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontrollers
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 16/32/64/128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 16/32/64K Bytes In-System Programmable Programmable
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet: