ST7FOXK1T6 STMicroelectronics, ST7FOXK1T6 Datasheet - Page 44

• Manufacturer Part Number: ST7FOXK1T6
• Description: IC MCU 8BIT 1V FLASH MEM 32LQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FOXK1T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: ST7FOXx
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: I2C
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7FLITE-SK/RAIS, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 1 Channel
• For Use With: 497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-6336

Supply, reset and clock management
6.4
Note:
6.4.1
Note:
Caution:
44/226
System Integrity management (SI)
The System Integrity Management block contains the Low voltage Detector (LVD).
Refer to
Low Voltage Detector (LVD)
The Low Voltage Detector function (LVD) generates a static reset when the V
voltage is below a V
as the power-down keeping the ST7 in reset.
The V
for power-on in order to avoid a parasitic reset when the MCU starts running and sinks
current on the supply (hysteresis).
The LVD Reset circuitry generates a reset when V
The LVD function is illustrated in
The voltage threshold can be enabled/disabled by option byte. See
211.
Provided the minimum V
the MCU can only be in two modes:
In these conditions, secure operation is always ensured for the application without the need
for external reset hardware.
During a Low Voltage Detector Reset, the RESET pin is held low, thus permitting the MCU
to reset other devices.
Use of LVD with capacitive power supply: with this type of power supply, if power cuts occur
in the application, it is recommended to pull V
conditions. Refer to circuit example in
The LVD is an optional function which can be selected by option byte. See
page
It allows the device to be used without any external RESET circuitry.
If the LVD is disabled, an external circuitry must be used to ensure a proper power-on reset.
It is recommended to make sure that the V
device is exiting from Reset, to ensure the application functions properly.
If an LVD reset occurs after a watchdog reset has occurred, the LVD will take priority and will
clear the watchdog flag.
A reset can also be triggered following the detection of an illegal opcode or prebyte code.
V
V
Under full software control
In static safe reset
211.
IT-(LVD)
IT+(LVD)
IT-(LVD)
Section 11.2.1 on page 184
reference value for a voltage drop is lower than the V
when V
when V
IT-(LVD)
DD
DD
is falling
DD
is rising
reference value. This means that it secures the power-up as well
value (guaranteed for the oscillator frequency) is above V
Figure
for further details.
Figure 89 on page 207
16.
DD
DD
supply voltage rises monotonously when the
down to 0 V to ensure optimum restart
DD
is below:
ST7FOXF1, ST7FOXK1, ST7FOXK2
and note 4.
IT+(LVD)
Section 13.1 on page
reference value
Section 13.1 on
DD
supply
IT-(LVD)
,