ST7FOXK1T6 STMicroelectronics, ST7FOXK1T6 Datasheet - Page 31

• Manufacturer Part Number: ST7FOXK1T6
• Description: IC MCU 8BIT 1V FLASH MEM 32LQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FOXK1T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: ST7FOXx
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: I2C
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7FLITE-SK/RAIS, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 1 Channel
• For Use With: 497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-6336

ST7FOXF1, ST7FOXK1, ST7FOXK2
Note:
Bit 3 = I Interrupt mask bit
Interrupts requested while I is set are latched and can be processed when I is cleared. By
default an interrupt routine is not interruptible because the I bit is set by hardware at the start
of the routine and reset by the IRET instruction at the end of the routine. If the I bit is cleared
by software in the interrupt routine, pending interrupts are serviced regardless of the priority
level of the current interrupt routine.
Bit 2 = N Negative bit
Bit 1 = Z Zero bit
Bit 0 = C Carry/borrow bit
Interrupt management bits
Bits 5,3 = I1, I0 Interrupt bits
This bit is set by hardware when entering in interrupt or by software to disable all
interrupts except the TRAP software interrupt. This bit is cleared by software.
0: Interrupts are enabled.
1: Interrupts are disabled.
This bit is controlled by the RIM, SIM and IRET instructions and is tested by the JRM
and JRNM instructions.
This bit is set and cleared by hardware. It is representative of the result sign of the last
arithmetic, logical or data manipulation. It is a copy of the 7
0: The result of the last operation is positive or null.
1: The result of the last operation is negative (that is, the most significant bit is a logic
1).
This bit is accessed by the JRMI and JRPL instructions.
This bit is set and cleared by hardware. This bit indicates that the result of the last
arithmetic, logical or data manipulation is zero.
0: The result of the last operation is different from zero.
1: The result of the last operation is zero.
This bit is accessed by the JREQ and JRNE test instructions.
This bit is set and cleared by hardware and software. It indicates an overflow or an
underflow has occurred during the last arithmetic operation.
0: No overflow or underflow has occurred.
1: An overflow or underflow has occurred.
This bit is driven by the SCF and RCF instructions and tested by the JRC and JRNC
instructions. It is also affected by the “bit test and branch”, shift and rotate instructions.
The combination of the I1 and I0 bits gives the current interrupt software priority.
These two bits are set/cleared by hardware when entering in interrupt. The loaded
value is given by the corresponding bits in the interrupt software priority registers
(IxSPR). They can be also set/cleared by software with the RIM, SIM, IRET, HALT, WFI
and PUSH/POP instructions. See
Section 9.6: Interrupts
for more details.
th
bit of the result.
Central processing unit
31/226