PIC18F4431-E/P Microchip Technology, PIC18F4431-E/P Datasheet - Page 207

• Manufacturer Part Number: PIC18F4431-E/P
• Description: IC MCU FLASH 8KX16 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4431-E/P

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, Power Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 768Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: EUSART, I2C, SPI, SSP
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 1 x 8
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 9 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP400 - DEVICE ADAPTER 18F4220 PDIP 40LDACICE0206 - ADAPTER MPLABICE 40P 600 MIL
• Lead Free Status / Rohs Status: Details

REGISTER 19-2:
 2010 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
Note 1:
WCOL
R/W-0
2:
3:
In Master mode, the overflow bit is not set since each new reception (and transmission) is initiated by
writing to the SSPBUF register.
When enabled, these pins must be properly configured as inputs or outputs.
Bit combinations not specifically listed here are either reserved or implemented in I
WCOL: Write Collision Detect bit
1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in
0 = No collision
SSPOV: Receive Overflow Indicator bit
In SPI mode:
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case
0 = No overflow
In I
1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV
0 = No overflow
SSPEN: Synchronous Serial Port Enable bit
In SPI mode:
1 = Enables serial port and configures SCK, SDO and SDI as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
In I
1 = Enables the serial port and configures the SDA and SCL pins as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
In both modes, when enabled, these pins must be properly configured as input or output.
CKP: Clock Polarity Select bit
In SPI mode:
1 = Idle state for clock is a high level
0 = Idle state for clock is a low level
In I
SCK release control.
1 = Enables clock
0 = Holds clock low (clock stretch). (Used to ensure data setup time.)
SSPOV
2
2
2
R/W-0
C™ mode:
C mode:
C mode:
software)
of overflow, the data in SSPSR is lost. Overflow can only occur in Slave mode. The user
must read the SSPBUF, even if only transmitting data, to avoid setting overflow. In
Master mode, the overflow bit is not set since each new reception (and transmission) is
initiated by writing to the SSPBUF register.
is a “don’t care” in Transmit mode. SSPOV must be cleared in software in either mode.
SSPCON: SYNCHRONOUS SERIAL PORT CONTROL REGISTER
(1)
W = Writable bit
‘1’ = Bit is set
SSPEN
R/W-0
(2)
PIC18F2331/2431/4331/4431
R/W-0
CKP
(1)
(2)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SSPM3
R/W-0
(3)
SSPM2
R/W-0
(3)
x = Bit is unknown
SSPM1
R/W-0
2
C™ mode only.
(3)
DS39616D-page 207
SSPM0
R/W-0
bit 0
(3)