AT91SAM9M10-CU Atmel, AT91SAM9M10-CU Datasheet - Page 759

• Manufacturer Part Number: AT91SAM9M10-CU
• Description: IC MCU 16/32BIT ARM9 324TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9M10-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 400MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, DMA, LCD, POR, PWM, WDT
• Number Of I /o: 160
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: ROM
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 1.1 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 324-TFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 133 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 2 x 16 bit
• Operating Supply Voltage: 1.65 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9M10-G45-EK
• Controller Family/series: AT91
• No. Of I/o's: 160
• Ram Memory Size: 64KB
• Cpu Speed: 400MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Cpu Family: AT91
• Device Core: ARM926EJ-S
• Device Core Size: 32b
• Frequency (max): 400MHz
• Total Internal Ram Size: 64KB
• # I/os (max): 160
• Number Of Timers - General Purpose: 7
• Operating Supply Voltage (typ): 1.8/2.5/3.3V
• Operating Supply Voltage (max): 1.1/1.95/3.6V
• Operating Supply Voltage (min): 0.9/1.65/1.8/3V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 324
• Package Type: TFBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

35.13.17 HSMCI Configuration Register
Name:
Addresses:
Access:
• FIFOMODE: HSMCI Internal FIFO control mode
0 = A write transfer starts when a sufficient amount of data is written into the FIFO.
When the block length is greater than or equal to 3/4 of the HSMCI internal FIFO size, then the write transfer starts as soon
as half the FIFO is filled. When the block length is greater than or equal to half the internal FIFO size, then the write transfer
starts as soon as one quarter of the FIFO is filled. In other cases, the transfer starts as soon as the total amount of data is
written in the internal FIFO.
1 = A write transfer starts as soon as one data is written into the FIFO.
• FERRCTRL: Flow Error flag reset control mode
0 = When an underflow/overflow condition flag is set, a new Write/Read command is needed to reset the flag.
1 = When an underflow/overflow condition flag is set, a read status resets the flag.
• HSMODE: High Speed Mode
0 = Default bus timing mode.
1 = If set to one, the host controller outputs command line and data lines on the rising edge of the card clock. The Host
driver shall check the high speed support in the card registers.
• LSYNC: Synchronize on the last block
0 = The pending command is sent at the end of the current data block.
1 = The pending command is sent at the end of the block transfer when the transfer length is not infinite (block count shall
be different from zero).
6355B–ATARM–21-Jun-10
31
23
15
–
–
7
–
30
22
14
HSMCI_CFG
0xFFF80054 (0), 0xFFFD0054 (1)
Read-write
–
–
6
–
29
21
13
–
–
–
5
–
FERRCTRL
LSYNC
28
20
12
–
–
4
27
19
11
–
–
–
3
–
26
18
10
–
–
–
2
–
AT91SAM9M10
25
17
–
–
9
–
1
–
FIFOMODE
HSMODE
24
16
–
–
8
0
759