AT91SAM9M10-CU Atmel, AT91SAM9M10-CU Datasheet - Page 242
AT91SAM9M10-CU
Manufacturer Part Number
AT91SAM9M10-CU
Description
IC MCU 16/32BIT ARM9 324TFBGA
Manufacturer
Atmel
Series
AT91SAMr
Specifications of AT91SAM9M10-CU
Core Processor
ARM9
Core Size
16/32-Bit
Speed
400MHz
Connectivity
EBI/EMI, Ethernet, I²C, SPI, SSC, UART/USART, USB
Peripherals
AC'97, DMA, LCD, POR, PWM, WDT
Number Of I /o
160
Program Memory Size
64KB (64K x 8)
Program Memory Type
ROM
Ram Size
128K x 8
Voltage - Supply (vcc/vdd)
0.9 V ~ 1.1 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
324-TFBGA
Processor Series
AT91SAMx
Core
ARM926EJ-S
Data Bus Width
32 bit
Data Ram Size
32 KB
Interface Type
2-Wire, SPI, USART
Maximum Clock Frequency
133 MHz
Number Of Programmable I/os
5
Number Of Timers
2 x 16 bit
Operating Supply Voltage
1.65 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
Development Tools By Supplier
AT91SAM-ICE, AT91-ISP, AT91SAM9M10-G45-EK
Controller Family/series
AT91
No. Of I/o's
160
Ram Memory Size
64KB
Cpu Speed
400MHz
No. Of Timers
2
Rohs Compliant
Yes
Cpu Family
AT91
Device Core
ARM926EJ-S
Device Core Size
32b
Frequency (max)
400MHz
Total Internal Ram Size
64KB
# I/os (max)
160
Number Of Timers - General Purpose
7
Operating Supply Voltage (typ)
1.8/2.5/3.3V
Operating Supply Voltage (max)
1.1/1.95/3.6V
Operating Supply Voltage (min)
0.9/1.65/1.8/3V
On-chip Adc
8-chx10-bit
Instruction Set Architecture
RISC
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
324
Package Type
TFBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT91SAM9M10-CU
Manufacturer:
Atmel
Quantity:
996
- Current page: 242 of 1404
- Download datasheet (22Mb)
To comply with SDRAM timing parameters, additional clock cycles are inserted between pre-
charge/active (Trp) commands and active/read (Trcd) commands. The DDRSDRC supports a
cas latency of two, two and half, and three (2 or 3 clocks delay). During this delay, the controller
uses internal signals to anticipate the next access and improve the performance of the control-
ler. Depending on the latency(2/3), the DDRSDRC anticipates 2 or 3 read accesses. In the case
of burst of specified length, accesses are not anticipated, but if the burst is broken (border, busy
mode, etc.), the next access is treated as an incrementing burst of unspecified length, and in
function of the latency(2/3), the DDRSDRC anticipates 2 or 3 read accesses.
For a definition of timing parameters, refer to
Section 22.7.3 “DDRSDRC Configuration Register”
on page
262.
Read accesses to the SDRAM are burst oriented and the burst length is programmed to 8. It
determines the maximum number of column locations that can be accessed for a given read
command. When the read command is issued, 8 columns are selected. All accesses for that
burst take place within these eight columns, meaning that the burst wraps within these 8 col-
umns if the boundary is reached. These 8 columns are selected by addr[13:3]; addr[2:0] is used
to select the starting location within the block.
In the case of incrementing burst (INCR/INCR4/INCR8/INCR16), the addresses can cross the
16-byte boundary of the SDRAM device. For example, when a transfer (INCR4) starts at
address 0x0C, the next access is 0x10, but since the burst length is programmed to 8, the next
access is 0x00. Since the boundary is reached, the burst wraps. The DDRSDRC takes into
account this feature of the SDRAM device. In the case of DDR-SDRAM devices, transfers start
at address 0x04/0x08/0x0C. In the case of SDR-SDRAM devices, transfers start at address
0x14/0x18/0x1C. Two read commands are issued to avoid wrapping when the boundary is
reached. The last read command may generate additional reading (1 read cmd = 4 DDR words
or 1 read cmd = 8 SDR words).
To avoid additional reading, it is possible to use the burst stop command to truncate the read
burst and to decrease power consumption.
AT91SAM9M10
242
6355B–ATARM–21-Jun-10
Related parts for AT91SAM9M10-CU
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MCU, MPU & DSP Development Tools KICKSTART KIT FOR AT91SAM9 PLUS
Manufacturer:
IAR Systems
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: