MC68332GCEH16 Freescale Semiconductor, MC68332GCEH16 Datasheet - Page 179

• Manufacturer Part Number: MC68332GCEH16
• Description: IC MCU 32BIT 16MHZ 132-PQFP
• Manufacturer: Freescale Semiconductor
• Series: M683xxr

Specifications of MC68332GCEH16

• Core Processor: CPU32
• Core Size: 32-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Type: ROMless
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 132-QFP
• Cpu Family: 68K/M683xx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 16MHz
• Interface Type: QSPI/SCI/UART
• Program Memory Size: Not Required
• Total Internal Ram Size: 2KB
• # I/os (max): 15
• Number Of Timers - General Purpose: 16
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 132
• Package Type: PQFP
• Controller Family/series: 68K
• No. Of I/o's: 15
• Ram Memory Size: 2KB
• Cpu Speed: 16MHz
• No. Of Timers: 16
• Embedded Interface Type: QSPI, SCI, UART
• Digital Ic Case Style: PQFP
• Rohs Compliant: Yes
• Processor Series: M683xx
• Core: CPU32
• Data Bus Width: 32 bit
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 16
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

MC68332
USER’S MANUAL
Notes For Tables 4 And 4a:
1. All internal registers retain data at 0 Hz.
2. This parameter is periodically sampled rather than 100% tested.
3. Assumes that a low-leakage external filter network is used to condition clock synthesizer input voltage. Total
4. Proper layout procedures must be followed to achieve specifications.
5. Assumes that stable V
6. Internal VCO frequency (f
7. Stability is the average deviation from the programmed frequency measured over the specified interval at max-
external resistance from the XFC pin due to external leakage must be greater than 15 M
specification. Filter network geometry can vary depending upon operating environment (See 4.3 System
Clock).
time V
for PLL lock after changing the W and Y frequency control bits in the synthesizer control register (SYNCR) while
the PLL is running, and to the period required for the clock to lock after LPSTOP.
by-two circuit that is not in the synthesizer feedback loop. When X = 0, the divider is enabled, and f
specified f
imum f
ternal clock signal. Noise injected into the PLL circuitry via V
frequency increase the C
trol system operation, this parameter should be measured during functional testing of the final system.
Num
4. When X = 1, the divider is disabled, and f
1
2
3
4
5
6
DD
sys
. Measurements are made with the device powered by filtered supplies and clocked by a stable ex-
and V
sys
Limp Mode Clock Frequency
CLKOUT Stability
PLL Reference Frequency Range
System Frequency
On-Chip PLL System Frequency
External Clock Operation
PLL Lock Time
VCO Frequency
.
SYNCR X bit = 0
SYNCR X bit = 1
Short term (5 s interval)
Long term (500 s interval)
DDSYN
Table A-4a. 20.97 MHz Clock Control Timing
(V
DD
DDSYN
are valid until RESET is released. This specification also applies to the period required
Freescale Semiconductor, Inc.
stab
Characteristic
and V
VCO
For More Information On This Product,
2,3,4,5
6
percentage for a given interval. When clock stability is a critical constraint on con-
is applied, and that the crystal oscillator is stable. Lock time is measured from the
) is determined by SYNCR W and Y bit values. The SYNCR X bit controls a divide-
2,3,4,7
ELECTRICAL CHARACTERISTICS
1
DDSYN
Go to: www.freescale.com
= 5.0 Vdc 5%, V
32.768 kHz reference
sys
= f
VCO
SS
Symbol
C
f
f
f
VCO
f
t
limp
= 0 Vdc, T
sys
stab
)
ref
lpll
2. X must equal one when operating at maximum
DDSYN
and V
A
= T
0.131
–0.05
–0.5
Min
25
dc
dc
—
—
—
—
L
SS
to T
and variation in crystal oscillator
H,
2 (f
f
sys
f
sys
20.97
20.97
20.97
sys
Max
0.05
0.5
50
20
max/2
max
max)
to guarantee this
MHz
MHz
MHz
Unit
kHz
ms
sys
= f
VCO
A-5