PIC18F67J10-I/PT Microchip Technology, PIC18F67J10-I/PT Datasheet - Page 96

• Manufacturer Part Number: PIC18F67J10-I/PT
• Description: IC PIC MCU FLASH 64KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F67J10-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: SPI/I2C/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 50
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183032, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• A/d Bit Size: 10 bit
• A/d Channels Available: 11
• Height: 1 mm
• Length: 10 mm
• Supply Voltage (max): 2.7 V, 3.6 V
• Supply Voltage (min): 2 V, 2.7 V
• Width: 10 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180015 - MODULE PLUG-IN 18F87J10 FOR HPCAC162062 - HEADER INTRFC MPLAB ICD2 64/80PAC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F87J10
7.3
While it may be assumed that external memory devices
will operate at the microcontroller clock rate, this is
often not the case. In fact, many devices require longer
times to write or retrieve data than the time allowed by
the execution of table read or table write operations.
To compensate for this, the external memory bus can
be configured to add a fixed delay to each table opera-
tion using the bus. Wait states are enabled by setting
the WAIT Configuration bit. When enabled, the amount
of
(MEMCON<5:4>). The delay is based on multiples of
microcontroller instruction cycle time and are added
following the instruction cycle when the table operation
is executed. The range is from no delay to 3 T
(default value).
7.4
With the exception of the upper address lines,
A19:A16, the pins associated with the external memory
bus are equipped with weak pull-ups. The pull-ups are
controlled by the upper three bits of the PORTG
register. They are named RDPU, REPU and RJPU and
control pull-ups on PORTD, PORTE and PORTJ,
respectively. Setting one of these bits enables the
corresponding pull-ups for that port. All pull-ups are
disabled by default on all device Resets.
7.5
The PIC18F87J10 family of devices are capable of
operating in one of two program memory modes, using
combinations of on-chip and external program memory.
The functions of the multiplexed port pins depend on
the program memory mode selected, as well as the
setting of the EBDIS bit.
In Microcontroller Mode, the bus is not active and the
pins have their port functions only. Writes to the
MEMCOM register are not permitted. The Reset value
of EBDIS (‘0’) is ignored and EMB pins behave as I/O
ports.
In Extended Microcontroller Mode, the external
program memory bus shares I/O port functions on the
pins. When the device is fetching or doing table
read/table write operations on the external program
memory space, the pins will have the external bus
function.
If the device is fetching and accessing internal program
memory locations only, the EBDIS control bit will
change the pins from external memory to I/O port
functions. When EBDIS = 0, the pins function as the
external bus. When EBDIS = 1, the pins function as I/O
ports.
DS39663D-page 94
delay
Wait States
Port Pin Weak Pull-ups
Program Memory Modes and the
External Memory Bus
is
set
by
the
WAIT1:WAIT0
Preliminary
bits
CY
If the device fetches or accesses external memory
while EBDIS = 1, the pins will switch to external bus. If
the EBDIS bit is set by a program executing from exter-
nal memory, the action of setting the bit will be delayed
until the program branches into the internal memory. At
that time, the pins will change from external bus to I/O
ports.
If the device is executing out of internal memory when
EBDIS = 0, the memory bus address/data and control
pins will not be active. They will go to a state where the
active address/data pins are tri-state; the CE, OE,
WRH, WRL, UB and LB signals are ‘1’ and ALE and
BA0 are ‘0’. Note that only those pins associated with
the current address width are forced to tri-state; the
other pins continue to function as I/O. In the case of
16-bit address width, for example, only AD<15:0>
(PORTD
(PORTH<3:0>) continue to function as I/O.
In all external memory modes, the bus takes priority
over any other peripherals that may share pins with it.
This includes the Parallel Slave Port and serial commu-
nications modules which would otherwise take priority
over the I/O port.
7.6
In 16-bit Data Width mode, the external memory
interface can be connected to external memories in
three different configurations:
• 16-bit Byte Write
• 16-bit Word Write
• 16-bit Byte Select
The configuration to be used is determined by the
WM1:WM0
(MEMCON<1:0>). These three different configurations
allow the designer maximum flexibility in using both
8-bit and 16-bit devices with 16-bit data.
For all 16-bit modes, the Address Latch Enable (ALE)
pin indicates that the address bits, AD<15:0>, are avail-
able on the external memory interface bus. Following
the address latch, the Output Enable signal (OE) will
enable both bytes of program memory at once to form
a 16-bit instruction word. The Chip Enable signal (CE)
is active at any time that the microcontroller accesses
external memory, whether reading or writing; it is
inactive (asserted high) whenever the device is in
Sleep mode.
In Byte Select mode, JEDEC standard Flash memories
will require BA0 for the byte address line and one I/O
line to select between Byte and Word mode. The other
16-bit modes do not need BA0. JEDEC standard static
RAM memories will use the UB or LB signals for byte
selection.
16-bit Data Width Modes
and
bits
PORTE)
in
© 2006 Microchip Technology Inc.
the
are
MEMCON
affected;
A19:A16
register