PIC18F67J10-I/PT Microchip Technology, PIC18F67J10-I/PT Datasheet - Page 225

• Manufacturer Part Number: PIC18F67J10-I/PT
• Description: IC PIC MCU FLASH 64KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F67J10-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: SPI/I2C/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 50
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183032, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• A/d Bit Size: 10 bit
• A/d Channels Available: 11
• Height: 1 mm
• Length: 10 mm
• Supply Voltage (max): 2.7 V, 3.6 V
• Supply Voltage (min): 2 V, 2.7 V
• Width: 10 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180015 - MODULE PLUG-IN 18F87J10 FOR HPCAC162062 - HEADER INTRFC MPLAB ICD2 64/80PAC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

18.4.9
A Repeated Start condition occurs when the RSEN bit
(SSPxCON2<1>) is programmed high and the I
module is in the Idle state. When the RSEN bit is set,
the SCLx pin is asserted low. When the SCLx pin is
sampled low, the Baud Rate Generator is loaded with
the contents of SSPxADD<5:0> and begins counting.
The SDAx pin is released (brought high) for one Baud
Rate Generator count (T
Generator times out, if SDAx is sampled high, the SCLx
pin will be deasserted (brought high). When SCLx is
sampled high, the Baud Rate Generator is reloaded
with the contents of SSPxADD<6:0> and begins
counting. SDAx and SCLx must be sampled high for
one T
the SDAx pin (SDAx = 0) for one T
high. Following this, the RSEN bit (SSPxCON2<1>) will
be automatically cleared and the Baud Rate Generator
will not be reloaded, leaving the SDAx pin held low. As
soon as a Start condition is detected on the SDAx and
SCLx pins, the S bit (SSPxSTAT<3>) will be set. The
SSPxIF bit will not be set until the Baud Rate Generator
has timed out.
FIGURE 18-22:
© 2006 Microchip Technology Inc.
BRG
Write to SSPxCON2
. This action is then followed by assertion of
I
START CONDITION TIMING
2
C MASTER MODE REPEATED
on falling edge of ninth clock,
RSEN bit set by hardware
REPEATED START CONDITION WAVEFORM
BRG
SDAx
SCLx
occurs here:
). When the Baud Rate
end of Xmit
BRG
SDAx = 1,
SCLx (no change).
while SCLx is
2
C logic
Preliminary
T
SDAx = 1,
SCLx = 1
BRG
Immediately following the SSPxIF bit getting set, the
user may write the SSPxBUF with the 7-bit address in
7-bit mode or the default first address in 10-bit mode.
After the first eight bits are transmitted and an ACK is
received, the user may then transmit an additional eight
bits of address (10-bit mode) or eight bits of data (7-bit
mode).
18.4.9.1
If the user writes the SSPxBUF when a Repeated Start
sequence is in progress, the WCOL is set and the
contents of the buffer are unchanged (the write doesn’t
occur).
T
BRG
Note:
Note 1: If RSEN is programmed while any other
Sr = Repeated Start
T
2: A bus collision during the Repeated Start
BRG
Because queueing of events is not
allowed, writing of the lower 5 bits of
SSPxCON2 is disabled until the Repeated
Start condition is complete.
event is in progress, it will not take effect.
condition occurs if:
• SDAx is sampled low when SCLx
• SCLx goes low before SDAx is
At completion of Start bit,
hardware clears RSEN bit
WCOL Status Flag
S bit set by hardware
goes from low-to-high.
asserted low. This may indicate that
another master is attempting to
transmit a data ‘1’.
and sets SSPxIF
Write to SSPxBUF occurs here
T
BRG
PIC18F87J10
1st bit
T
BRG
DS39663D-page 223