PIC18F67J10-I/PT Microchip Technology, PIC18F67J10-I/PT Datasheet - Page 203

• Manufacturer Part Number: PIC18F67J10-I/PT
• Description: IC PIC MCU FLASH 64KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F67J10-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: SPI/I2C/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 50
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183032, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• A/d Bit Size: 10 bit
• A/d Channels Available: 11
• Height: 1 mm
• Length: 10 mm
• Supply Voltage (max): 2.7 V, 3.6 V
• Supply Voltage (min): 2 V, 2.7 V
• Width: 10 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180015 - MODULE PLUG-IN 18F87J10 FOR HPCAC162062 - HEADER INTRFC MPLAB ICD2 64/80PAC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

REGISTER 18-4:
© 2006 Microchip Technology Inc.
bit 7
bit 6
bit 5
bit 4
bit 3-0
SSPxCON1: MSSPx CONTROL REGISTER 1 (I
bit 7
WCOL: Write Collision Detect bit
In Master Transmit mode:
1 = A write to the SSPxBUF register was attempted while the I
0 = No collision
In Slave Transmit mode:
1 = The SSPxBUF register is written while it is still transmitting the previous word (must be
0 = No collision
In Receive mode (Master or Slave modes):
This is a “don’t care” bit.
SSPOV: Receive Overflow Indicator bit
In Receive mode:
1 = A byte is received while the SSPxBUF register is still holding the previous byte (must be
0 = No overflow
In Transmit mode:
This is a “don’t care” bit in Transmit mode.
SSPEN: Master Synchronous Serial Port Enable bit
1 = Enables the serial port and configures the SDAx and SCLx pins as the serial port pins
0 = Disables serial port and configures these pins as I/O port pins
CKP: SCKx Release Control bit
In Slave mode:
1 = Release clock
0 = Holds clock low (clock stretch), used to ensure data setup time
In Master mode:
Unused in this mode.
SSPM3:SSPM0: Master Synchronous Serial Port Mode Select bits
1111 = I
1110 = I
1011 = I
1000 = I
0111 = I
0110 = I
Bit combinations not specifically listed here are either reserved or implemented in SPI mode only.
Legend:
R = Readable bit
-n = Value at POR
WCOL
R/W-0
Note:
a transmission to be started (must be cleared in software)
cleared in software)
cleared in software)
2
2
2
2
2
2
C Slave mode, 10-bit address with Start and Stop bit interrupts enabled
C Slave mode, 7-bit address with Start and Stop bit interrupts enabled
C Firmware Controlled Master mode (slave Idle)
C Master mode, clock = F
C Slave mode, 10-bit address
C Slave mode, 7-bit address
When enabled, the SDAx and SCLx pins must be configured as inputs.
SSPOV
R/W-0
W = Writable bit
‘1’ = Bit is set
SSPEN
R/W-0
Preliminary
OSC
R/W-0
CKP
/(4 * (SSPxADD + 1))
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SSPM3
R/W-0
2
C™ MODE)
PIC18F87J10
SSPM2
R/W-0
2
C conditions were not valid for
x = Bit is unknown
SSPM1
R/W-0
DS39663D-page 201
SSPM0
R/W-0
bit 0