Z16F2800100ZCOG Zilog, Z16F2800100ZCOG Datasheet - Page 310
Z16F2800100ZCOG
Manufacturer Part Number
Z16F2800100ZCOG
Description
DEV KIT FOR Z16F ZNEO
Manufacturer
Zilog
Series
ZNEO™r
Type
MCUr
Datasheets
1.Z16F2800100ZCOG.pdf
(2 pages)
2.Z16F2800100ZCOG.pdf
(30 pages)
3.Z16F2800100ZCOG.pdf
(388 pages)
Specifications of Z16F2800100ZCOG
Contents
Evaluation Board, Software and Documentation
For Use With/related Products
Z16F Series
For Use With
269-4661 - KIT ACC ETHERNET SMART CABLE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
269-4537
- Current page: 310 of 388
- Download datasheet (22Mb)
Table 158. Option Bits At Program Memory Address 0000H
PS022008-0810
BITS
FIELD
RESET
R/W
ADDR
Note: U = Unchanged by Reset. R/W = Read/Write.
Program Memory Address 0000H
R/W
OSC_SEL[1:0]
U
7
Option bits in this space are altered to change the chip configuration at reset.
OSC_SEL[1:0]—Oscillator mode selection
00 = On-chip oscillator configured for use with external RC networks (<4 MHz).
01 = Minimum power for use with very low frequency crystals (32 kHz to 1.0 MHz).
10 = Medium power for use with medium frequency crystals or ceramic resonators
(0.5 MHz to 10.0 MHz).
11 = Maximum power for use with high frequency crystals (8.0 MHz to 20.0 MHz). This
setting is the default for unprogrammed (erased) Flash.
WDT_RES—WDT Reset
0 = WDT time-out generates an interrupt request. Interrupts must be globally enabled for
the ZNEO CPU to acknowledge the interrupt request.
1 = WDT time-out causes a Short Reset. This setting is the default for unprogrammed
(erased) Flash.
WDT_AO—WDT always on
0 = WDT is automatically enabled after reset. The WDT oscillator is disabled by clearing
the WDTEN bit in the OSCCTL register.
1 = WDT is enabled upon execution of the
disabled by clearing the WDTEN bit in the OSCCTL register.
VBO_AO—Voltage Brownout protection always on
0 = Voltage Brownout protection is disabled in STOP mode to reduce total power
consumption.
1 = Voltage Brownout protection is always enabled, including during STOP mode. This
setting is the default for unprogrammed (erased) Flash.
DBGUART—Debug UART enable
0 = The Debug UART option is enabled.
1 = The Debug UART option is disabled.
R/W
U
6
WDT_RES WDT_AO
R/W
U
5
P R E L I M I N A R Y
Program Memory 0000H
R/W
U
4
WDT
VBO_AO
R/W
instruction. The WDT oscillator is
U
3
DBGUART
R/W
U
2
Product Specification
ZNEO
FWP
R/W
U
1
Z16F Series
Option Bits
R/W
RP
U
0
294
Related parts for Z16F2800100ZCOG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: