Z16F2800100ZCOG Zilog, Z16F2800100ZCOG Datasheet - Page 212
Z16F2800100ZCOG
Manufacturer Part Number
Z16F2800100ZCOG
Description
DEV KIT FOR Z16F ZNEO
Manufacturer
Zilog
Series
ZNEO™r
Type
MCUr
Datasheets
1.Z16F2800100ZCOG.pdf
(2 pages)
2.Z16F2800100ZCOG.pdf
(30 pages)
3.Z16F2800100ZCOG.pdf
(388 pages)
Specifications of Z16F2800100ZCOG
Contents
Evaluation Board, Software and Documentation
For Use With/related Products
Z16F Series
For Use With
269-4661 - KIT ACC ETHERNET SMART CABLE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
269-4537
- Current page: 212 of 388
- Download datasheet (22Mb)
®
ZNEO
Z16F Series
Product Specification
196
is detected in the Slave by SS changing state. The SS framing signal will lead the frame by
one SCK period. In this mode SCK will run continuously, starting with the initial SS
assertion. Frames will run back-to-back as long as software/DMA continue to provide
2
data. The I
S protocol (Inter IC Sound) is used to carry left and right channel audio data
with the SS signal indicating which channel is being sent. In Slave mode, the change in
state of SS (Low to High or High to Low) will trigger the start of a transaction on the next
SCK cycle.
NUMBITS[2:0]—Number of Data Bits Per Character to Transfer
This field contains the number of bits to shift for each character transfer. For information
on valid bit positions when the character length is less than 8-bits, see
ESPI Data Register
description on page 191.
000 = 8 bits
001 = 1 bit
010 = 2 bits
011 = 3 bits
100 = 4 bits
101 = 5 bits
110 = 6 bits
111 = 7 bits
SSIO—Slave Select I/O
This bit controls the direction of the SS pin. In single Master mode, SSIO is set to 1 unless
a separate GPIO pin is being used to provide the SS output function. In the SPI Slave or
Multi-Master configuration SSIO is set to 0.
0 = SS pin configured as an input (SPI Slave and Multi-Master modes)
1 = SS pin configured as an output (SPI single Master mode)
SSPO—Slave Select Polarity
This bit controls the polarity of the SS pin.
0 = SS is active Low. (SSV = 1 corresponds to SS = 0)
1 = SS is active High. (SSV = 1 corresponds to SS = 1)
PS022008-0810
P R E L I M I N A R Y
Enhanced Serial Peripheral Interface
Related parts for Z16F2800100ZCOG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: