Z16F2800100ZCOG Zilog, Z16F2800100ZCOG Datasheet - Page 210
Z16F2800100ZCOG
Manufacturer Part Number
Z16F2800100ZCOG
Description
DEV KIT FOR Z16F ZNEO
Manufacturer
Zilog
Series
ZNEO™r
Type
MCUr
Datasheets
1.Z16F2800100ZCOG.pdf
(2 pages)
2.Z16F2800100ZCOG.pdf
(30 pages)
3.Z16F2800100ZCOG.pdf
(388 pages)
Specifications of Z16F2800100ZCOG
Contents
Evaluation Board, Software and Documentation
For Use With/related Products
Z16F Series
For Use With
269-4661 - KIT ACC ETHERNET SMART CABLE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
269-4537
- Current page: 210 of 388
- Download datasheet (22Mb)
PS022008-0810
Caution:
10 = TRANSMIT ONLY Mode
11 = TRANSMIT/RECEIVE Mode
BRGCTL—Baud Rate Generator Control
The function of this bit depends upon ESPIEN1,0. When ESPIEN1,0 = 00, this bit allows
enabling the BRG to provide periodic interrupts.
If the ESPI is disabled (
0 = The BRG timer function is disabled.
1 = The BRG timer function and time-out interrupt are enabled.
If the ESPI is enabled:
0 = Reading the Baud Rate High and Low registers returns the BRG Reload value.
1 = Reading the Baud Rate High and Low registers returns the BRG Counter value.
If reading the counter one byte at a time while the BRG is counting keep in mind
that the values will not be in sync. It is recommended to read the counter using word
(2-byte) reads.
PHASE—Phase Select
Sets the phase relationship of the data to the clock. For more information on operation of
the PHASE bit, see
CLKPOL—Clock Polarity
0 = SCK idles Low (0).
1 = SCK idles High (1).
WOR—Wire-OR (Open-Drain) Mode Enabled
0 = ESPI signal pins not configured for open-drain.
1 = All four ESPI signal pins (SCK, SS, MISO, MOSI) configured for open-drain
If
function. This setting is used for Multi-Master and/or Multi-Slave configurations.
Reading the Baud Rate High and Low registers returns the BRG Reload value.
Reading the Baud Rate High and Low registers returns the BRG Counter value.
If
disabled.
enabled to provide a Slave SCK timeout. See Slave Abort error description.
Use this setting if the software application is both sending and receiving information.
In MASTER mode software must still write to the Transmit Data register to initiate
the transfer.
requests
not occur.
Use this setting in MASTER or SLAVE mode when the software application is
sending data but not receiving. RDRF will assert, but receive interrupt and DMA
Both TDRE and RDRF will be active.
MMEN = 1
MMEN = 1
, the BRG is enabled to generate SCK. If
, the BRG is enabled to generate SCK. If
ESPI Clock Phase and Polarity Control
ESPIEN1, ESPIEN0 = 00
P R E L I M I N A R Y
):
Enhanced Serial Peripheral Interface
MMEN = 0
MMEN = 0
on page 180.
Product Specification
, the BRG is
ZNEO
, the BRG is
Z16F Series
194
Related parts for Z16F2800100ZCOG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: