Z16F2800100ZCOG Zilog, Z16F2800100ZCOG Datasheet - Page 226
Z16F2800100ZCOG
Manufacturer Part Number
Z16F2800100ZCOG
Description
DEV KIT FOR Z16F ZNEO
Manufacturer
Zilog
Series
ZNEO™r
Type
MCUr
Datasheets
1.Z16F2800100ZCOG.pdf
(2 pages)
2.Z16F2800100ZCOG.pdf
(30 pages)
3.Z16F2800100ZCOG.pdf
(388 pages)
Specifications of Z16F2800100ZCOG
Contents
Evaluation Board, Software and Documentation
For Use With/related Products
Z16F Series
For Use With
269-4661 - KIT ACC ETHERNET SMART CABLE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
269-4537
- Current page: 226 of 388
- Download datasheet (22Mb)
PS022008-0810
When a Master loses arbitration, software is informed by means of the Arbitration Lost
interrupt. Software repeats the same transaction again at a later time.
A special case occurs when a slave transaction starts just before software attempts to start
a new master transaction by setting the
slave states before the START bit is set and the I
address match occurs and the I
cleared and an Arbitration Lost interrupt is asserted. Software minimizes the chance of this
occurring by checking the BUSY bit in the I2CSTATE register before initiating a master
transaction. If a slave address match does not occur, the Arbitration Lost interrupt does not
occur and the
once the I
Master Address Only Transactions
It is sometimes appropriate to perform an address-only transaction to determine if a
particular Slave device is able to respond. This transaction is performed by monitoring the
ACKV bit in the I2CSTATE register after the address has been written to the I2CDATA
register and the START bit has been set. Once ACKV is set, the ACK bit in the I2CSTATE
register determines if the Slave is able to communicate. The STOP bit must be set in the
I2CCTL register to terminate the transaction without transferring data. For a 10-bit slave
address, if the first address byte is acknowledged, the second address byte must also be
sent to determine if the appropriate slave is responding.
Another approach is to set both the STOP and START bits (for sending a 7-bit address).
Once both bits are cleared (7-bit address has been sent and transaction is complete), the
ACK
bit after the second TDRE interrupt (second address byte is being sent).
Master Transaction Diagrams
In the following transaction diagrams, shaded regions indicate data transferred from the
Master to the Slave and unshaded regions indicate data transferred from the Slave to the
Master. The transaction field labels are defined as follows:
•
•
•
•
•
Master Write Transaction with a 7-Bit Address
Figure 43
Slave.
S — Start
W — Write
A — Acknowledge
A — Not Acknowledge
P — Stop
bit is read to determine if the slave is acknowledged. For a 10-bit slave, set the STOP
2
on page 211 displays the data transfer format from a Master to a 7-bit addressed
C bus is no longer busy.
START
bit is not cleared. The I
P R E L I M I N A R Y
2
C Controller receives or transmits data, the
START
2
C Controller initiates the master transaction
bit. In this case the state machine enters the
2
C Controller does not arbitrate. If a slave
I
2
C Master/Slave Controller
Product Specification
ZNEO
START
Z16F Series
bit is
210
Related parts for Z16F2800100ZCOG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: