SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 846

• Manufacturer Part Number: SAM9XE512
• Manufacturer: Atmel Corporation

Specifications of SAM9XE512

• Flash (kbytes): 512 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 180 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 6
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 312
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.65 to 1.95
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

846
Doc
Rev.
6254C
AT91SAM9XE128/256/512 Preliminary
Comments (Continued)
Electrical Characteristics:
Table 43-2, “DC
I
Table 43-5, “Power Consumption for Different
deactivated”. Footnote
Section 43.8 “Core Power Supply POR
Table 43-25, “Maximum MCK Frequency vs. Embedded Flash Wait
Table 43-18, “PLLB
Table 43-24, “Power-On-Reset
Section 43.9 “Power-up
Section 43.10 “Power-down
Section 43.12.1 “Timing
Table
Section 43.13.1 “Timing
Table 43-32
Section 43.15.3.1 “Timing
Table 43-44
“SPI”,
Errata:
Section 46.2.2 “Error Corrected Code Controller
NRD/NWE
Section 46.2.3 “MultiMedia Card Interface (MCI)”
“MCI: Data Timeout Error Flag”, removed from errata.
“MCI: Small Block
“MCI: old SDCard
“RSTC: Reset During SDRAM Accesses”, removed from errata.
Section 46.2.6 “Serial Peripheral Interface (SPI)”
“SPI: Baudrate Set to 1”, removed from errata.
“SPI: Inaccurate RHR.PCS in Variable
Section 46.2.7 “Serial Synchronous Controller (SSC)”
“SSC: Periodic Transmission Limitations in Master Mode”, removed from errata.
“SSC: Clock is Transmitted before the SSC is Enabled, removed from errata.
“SSC: Delay on TD (transmit data
“SSC: Data sent without any frame
Section 46.2.8 “Two-wire Interface (TWI)”
“TWI: Software
“TWI: Overrun in Master Read
Section 46.2.10 “Universal Synchronous Asycnchronous Receiver Transmitter (USART)”
“USART: Slave Synchronous
“USART: Number of Errors Register (US_NER) ISO7816 error
O
output current for PA0-PA31 PB0-PB31 PC0-PC3 is 8 mA.
43-27, updated: Corner removed from capacitance load table.
Figure
pulse”, added to errata.
and
updated: Corner removed from capacitance load table.
43-6,
Reset”, added to errata.
Characteristics”, Min pull up resistance values updated.
Table 43-32
Reading”, added to errata.
Compatibility”, added to errata.
Figure
Characteristics”, startup time added.
(1)
Sequence”, instructions updated. schematic removed.
Conditions”, updated: SMC timings are given in worst case conditions.
Conditions”, updated: SDRAMC timings are given in worst case conditions.
removed from title.
43-7,
Conditions”, updated: SSC timings are given in worst case conditions.
Sequence”, instructions updated.
updated: Corner removed from capacitance load tables.
Mode”, added to errata.
Mode”, added to errata.
Characteristics”, irrelevant rows removed.
Figure
signal)”, added to errata.
synchro”, added to errata.
Mode”, added to errata.
43-8,
Characteristics”, updated this section.
Figure
Modes”, Active mode updated: “all peripheral clocks
(ECC)”,
43-9, confusing titles to SPI timing diagrams simplified.
“ECC: Computation with a 1 clock cycle long
number”, added to errata.
States”, updated.
6254C–ATARM–22-Jan-10
Change
Request
Ref.
6602
rfo
6343
6883
6386
6957
6957/6963
rfo
6872/6766
6465/6889
6889
6889
6889
6889
6889
6889
6465/6889
6889
6889
6465/6889