SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 458
SAM9XE512
Manufacturer Part Number
SAM9XE512
Description
Manufacturer
Atmel Corporation
Datasheets
1.SAM9260.pdf
(290 pages)
2.SAM9261.pdf
(248 pages)
3.SAM9XE128.pdf
(860 pages)
4.SAM9XE128.pdf
(48 pages)
Specifications of SAM9XE512
Flash (kbytes)
512 Kbytes
Pin Count
217
Max. Operating Frequency
180 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
96
Ext Interrupts
96
Usb Transceiver
3
Usb Speed
Full Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
2
Uart
6
Ssc
1
Ethernet
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
Yes
Adc Channels
4
Adc Resolution (bits)
10
Adc Speed (ksps)
312
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
NO
External Bus Interface
1
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.65 to 1.95
Fpu
No
Mpu / Mmu
No / Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- SAM9260 PDF datasheet
- SAM9261 PDF datasheet #2
- SAM9XE128 PDF datasheet #3
- SAM9XE128 PDF datasheet #4
- Current page: 458 of 860
- Download datasheet (13Mb)
33.7.7
33.7.7.1
33.7.7.2
33.7.8
33.7.9
458
AT91SAM9XE128/256/512 Preliminary
Using the Peripheral DMA Controller (PDC)
SMBUS Quick Command (Master Mode Only)
Read-write Flowcharts
Data Transmit with the PDC
Data Receive with the PDC
The use of the PDC significantly reduces the CPU load.
To assure correct implementation, respect the following programming sequences:
The TWI interface can perform a Quick Command:
Figure 33-14. SMBUS Quick Command
The following flowcharts shown in
33-18 on page
read and write operations. A polling or interrupt method can be used to check the status bits.
The interrupt method requires that the interrupt enable register (TWI_IER) be configured first.
1. Initialize the transmit PDC (memory pointers, size, etc.).
2. Configure the master mode (DADR, CKDIV, etc.).
3. Start the transfer by setting the PDC TXTEN bit.
4. Wait for the PDC end TX flag.
5. Disable the PDC by setting the PDC TXDIS bit.
1. Initialize the receive PDC (memory pointers, size - 1, etc.).
2. Configure the master mode (DADR, CKDIV, etc.).
3. Start the transfer by setting the PDC RXTEN bit.
4. Wait for the PDC end RX flag.
5. Disable the PDC by setting the PDC RXDIS bit.
1. Configure the master mode (DADR, CKDIV, etc.).
2. Write the MREAD bit in the TWI_MMR register at the value of the one-bit command to
3. Start the transfer by setting the QUICK bit in the TWI_CR.
be sent.
462,
Figure 33-19 on page 463
TXCOMP
Write QUICK command in TWI_CR
TXRDY
TWD
Figure 33-16 on page
S
DADR
and
Figure 33-20 on page 464
R/W
460,
A
Figure 33-17 on page
P
6254C–ATARM–22-Jan-10
give examples for
461,
Figure
Related parts for SAM9XE512
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: