SAM9XE512 Atmel Corporation, SAM9XE512 Datasheet - Page 178

• Manufacturer Part Number: SAM9XE512
• Manufacturer: Atmel Corporation

Specifications of SAM9XE512

• Flash (kbytes): 512 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 180 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 6
• Ssc: 1
• Ethernet: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 312
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.65 to 1.95
• Fpu: No
• Mpu / Mmu: No / Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

22.6.6.1
22.6.6.2
178
AT91SAM9XE128/256/512 Preliminary
I/O Mode, Common Memory Mode, Attribute Memory Mode and True IDE Mode
CFCE1 and CFCE2 Signals
Within the NCS4 and/or NCS5 address space, the current transfer address is used to distinguish
I/O mode, common memory mode, attribute memory mode and True IDE mode.
The different modes are accessed through a specific memory mapping as illustrated on
22-3. A[23:21] bits of the transfer address are used to select the desired mode as described in
Table 22-5 on page
Figure 22-3. CompactFlash Memory Mapping
Note:
Table 22-5.
To cover all types of access, the SMC must be alternatively set to drive 8-bit data bus or 16-bit
data bus. The odd byte access on the D[7:0] bus is only possible when the SMC is configured to
drive 8-bit memory devices on the corresponding NCS pin (NCS4 or NCS5). The Chip Select
Register (DBW field in the corresponding Chip Select Register) of the NCS4 and/or NCS5
address space must be set as shown in
NBS1 and NBS0 are the byte selection signals from SMC and are available when the SMC is set
in Byte Select mode on the corresponding Chip Select.
A[23:21]
000
010
100
110
111
The A22 pin is used to drive the REG signal of the CompactFlash Device (except in True IDE
mode).
CF Address Space
CompactFlash Mode Selection
178.
Offset 0x00E0 0000
Offset 0x00C0 0000
Offset 0x0080 0000
Offset 0x0040 0000
Offset 0x0000 0000
Table 22-6
to enable the required access type.
Alternate True IDE Mode
Mode Base Address
Common Memory Mode Space
Common Memory
True IDE Alternate Mode Space
Attribute Memory Mode Space
Attribute Memory
True IDE Mode
True IDE Mode Space
I/O Mode
I/O Mode Space
6254C–ATARM–22-Jan-10
Figure