SAM7X256 Atmel Corporation, SAM7X256 Datasheet - Page 586

• Manufacturer Part Number: SAM7X256
• Manufacturer: Atmel Corporation

Specifications of SAM7X256

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 62
• Ext Interrupts: 62
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 3
• Can: 1
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

37.5.8
Register Name:
Access Type:
• MFD: Management Frame Done
The PHY maintenance register has completed its operation. Cleared on read.
• RCOMP: Receive Complete
A frame has been stored in memory. Cleared on read.
• RXUBR: Receive Used Bit Read
Set when a receive buffer descriptor is read with its used bit set. Cleared on read.
• TXUBR: Transmit Used Bit Read
Set when a transmit buffer descriptor is read with its used bit set. Cleared on read.
• TUND: Ethernet Transmit Buffer Underrun
The transmit DMA did not fetch frame data in time for it to be transmitted or hresp returned not OK. Also set if a used bit
is read mid-frame or when a new transmit queue pointer is written. Cleared on read.
• RLE: Retry Limit Exceeded
Cleared on read.
• TXERR: Transmit Error
Transmit buffers exhausted in mid-frame - transmit error. Cleared on read.
• TCOMP: Transmit Complete
Set when a frame has been transmitted. Cleared on read.
• ROVR: Receive Overrun
Set when the receive overrun status bit gets set. Cleared on read.
• HRESP: Hresp not OK
Set when the DMA block sees a bus error. Cleared on read.
• PFR: Pause Frame Received
Indicates a valid pause has been received. Cleared on a read.
• PTZ: Pause Time Zero
Set when the pause time register, 0x38 decrements to zero. Cleared on a read.
586
TCOMP
31
23
15
–
–
–
7
SAM7X512/256/128
Interrupt Status Register
TXERR
30
22
14
EMAC_ISR
–
–
–
6
Read-write
RLE
PTZ
29
21
13
–
–
5
TUND
PFR
28
20
12
–
–
4
HRESP
TXUBR
27
19
11
–
–
3
RXUBR
ROVR
26
18
10
–
–
2
RCOMP
25
17
–
–
9
1
6120I–ATARM–06-Apr-11
MFD
24
16
–
–
8
–
0