SAM7X256 Atmel Corporation, SAM7X256 Datasheet - Page 237

• Manufacturer Part Number: SAM7X256
• Manufacturer: Atmel Corporation

Specifications of SAM7X256

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 62
• Ext Interrupts: 62
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 3
• Can: 1
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

27.5
6120I–ATARM–06-Apr-11
I/O Lines Programming Example
The programing example as shown in
configuration.
Table 27-1.
• 4-bit output port on I/O lines 0 to 3, (should be written in a single write operation), open-drain,
• Four output signals on I/O lines 4 to 7 (to drive LEDs for example), driven high and low, no
• Four input signals on I/O lines 8 to 11 (to read push-button states for example), with pull-up
• Four input signals on I/O line 12 to 15 to read an external device status (polled, thus no input
• I/O lines 16 to 19 assigned to peripheral A functions with pull-up resistor
• I/O lines 20 to 23 assigned to peripheral B functions, no pull-up resistor
• I/O line 24 to 27 assigned to peripheral A with Input Change Interrupt and pull-up resistor
with pull-up resistor
pull-up resistor
resistors, glitch filters and input change interrupts
change interrupt), no pull-up resistor, no glitch filter
PIO_OWER
PIO_OWDR
PIO_SODR
PIO_CODR
PIO_MDER
PIO_MDDR
PIO_PUDR
PIO_PUER
PIO_ODR
PIO_IFER
PIO_IFDR
PIO_PDR
PIO_OER
PIO_PER
PIO_ASR
PIO_BSR
Register
PIO_IDR
PIO_IER
Programming Example
Table 27-1
below is used to define the following
Value to be Written
0x0FFF F0FF
0x0FFF FFFF
0x0FFF FFF0
0x0FFF FFF0
0x0000 FFFF
0x0FFF 0000
0x0FFF FF00
0x00FF F0FF
0x0F0F FF0F
0x0000 00FF
0x0000 0F00
0x0F00 0F00
0x0000 000F
0x00F0 00F0
0x0F0F 0000
0x00F0 0000
0x0000 000F
SAM7X512/256/128
0x0000 0000
237