SAM7X256 Atmel Corporation, SAM7X256 Datasheet - Page 521
SAM7X256
Manufacturer Part Number
SAM7X256
Description
Manufacturer
Atmel Corporation
Specifications of SAM7X256
Flash (kbytes)
256 Kbytes
Pin Count
100
Max. Operating Frequency
55 MHz
Cpu
ARM7TDMI
Hardware Qtouch Acquisition
No
Max I/o Pins
62
Ext Interrupts
62
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
2
Twi (i2c)
1
Uart
3
Can
1
Ssc
1
Ethernet
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
64
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
3.3
Operating Voltage (vcc)
3.0 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 521 of 687
- Download datasheet (11Mb)
36.7.3
36.7.3.1
36.7.3.2
Figure 36-11. Receive Mailbox
Note:
6120I–ATARM–06-Apr-11
(CAN_MSRx)
(CAN_MSRx)
CAN_MDHx)
(CAN_MCRx)
(CAN_MDLx
In the case of ARM architecture, CAN_MSRx, CAN_MDLx, CAN_MDHx can be read using an optimized ldm assembler
instruction.
CAN BUS
CAN Controller Message Handling
MRDY
Receive Handling
MTCR
Simple Receive Mailbox
MMI
Reading CAN_MDHx & CAN_MDLx
Two modes are available to configure a mailbox to receive messages. In Receive Mode, the
first message received is stored in the mailbox data register. In Receive with Overwrite Mode,
the last message received is stored in the mailbox.
A mailbox is in Receive Mode once the MOT field in the CAN_MMRx register has been config-
ured. Message ID and Message Acceptance Mask must be set before the Receive Mode is
enabled.
After Receive Mode is enabled, the MRDY flag in the CAN_MSR register is automatically
cleared until the first message is received. When the first message has been accepted by the
mailbox, the MRDY flag is set. An interrupt is pending for the mailbox while the MRDY flag is set.
This interrupt can be masked depending on the mailbox flag in the CAN_IMR global register.
Message data are stored in the mailbox data register until the software application notifies that
data processing has ended. This is done by asking for a new transfer command, setting the
MTCR flag in the CAN_MCRx register. This automatically clears the MRDY signal.
The MMI flag in the CAN_MSRx register notifies the software that a message has been lost by
the mailbox. This flag is set when messages are received while MRDY is set in the CAN_MSRx
register. This flag is cleared by reading the CAN_MSRs register. A receive mailbox prevents
from overwriting the first message by new ones while MRDY flag is set in the CAN_MSRx regis-
ter. See
Message 1
Figure
36-11.
Reading CAN_MSRx
Message 2 lost
Message 1
Writing CAN_MCRx
Message 3
SAM7X512/256/128
Message 3
Message ID = CAN_MIDx
521
Related parts for SAM7X256
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: