SAM7X256 Atmel Corporation, SAM7X256 Datasheet - Page 465

• Manufacturer Part Number: SAM7X256
• Manufacturer: Atmel Corporation

Specifications of SAM7X256

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 62
• Ext Interrupts: 62
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 3
• Can: 1
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

34.5.3.7
34.5.3.8
6120I–ATARM–06-Apr-11
Receiving a Host Resume
Sending a Device Remote Wakeup
register.This flag is cleared by writing to the UDP_ICR register. Then the device enters Suspend
Mode.
In this state bus powered devices must drain less than 500uA from the 5V VBUS. As an exam-
ple, the microcontroller switches to slow clock, disables the PLL and main oscillator, and goes
into Idle Mode. It may also switch off other devices on the board.
The USB device peripheral clocks can be switched off. Resume event is asynchronously
detected. MCK and UDPCK can be switched off in the Power Management controller and the
USB transceiver can be disabled by setting the TXVDIS field in the UDP_TXVC register.
Warning: Read, write operations to the UDP registers are allowed only if MCK is enabled for the
UDP peripheral. Switching off MCK for the UDP peripheral must be one of the last operations
after writing to the UDP_TXVC and acknowledging the RXSUSP.
In suspend mode, a resume event on the USB bus line is detected asynchronously, transceiver
and clocks are disabled (however the pullup shall not be removed).
Once the resume is detected on the bus, the WAKEUP signal in the UDP_ISR is set. It may gen-
erate an interrupt if the corresponding bit in the UDP_IMR register is set. This interrupt may be
used to wake up the core, enable PLL and main oscillators and configure clocks.
Warning: Read, write operations to the UDP registers are allowed only if MCK is enabled for the
UDP peripheral. MCK for the UDP must be enabled before clearing the WAKEUP bit in the
UDP_ICR register and clearing TXVDIS in the UDP_TXVC register.
In Suspend state it is possible to wake up the host sending an external resume.
To force a K state to the bus (DM at 3.3V and DP tied to GND), it is possible to use a transistor
to connect a pullup on DM. The K state is obtained by disabling the pullup on DP and enabling
the pullup on DM. This should be under the control of the application.
Figure 34-15. Board Schematic to Drive a K State
• The device must wait at least 5 ms after being entered in suspend before sending an external
• The device has 10 ms from the moment it starts to drain current and it forces a K state to
• The device must force a K state from 1 to 15 ms to resume the host
resume.
resume the host.
PIO
0: Force Wake UP (K State)
1: Normal Mode
SAM7X512/256/128
DM
3V3
1.5 K
465