ADF4193BCPZ Analog Devices Inc, ADF4193BCPZ Datasheet - Page 27

• Manufacturer Part Number: ADF4193BCPZ
• Description: IC PLL FREQ SYNTHESIZER 32LFCSP
• Manufacturer: Analog Devices Inc
• Type: Clock/Frequency Synthesizer (RF)r

Specifications of ADF4193BCPZ

• Pll: Yes
• Input: CMOS
• Output: Clock
• Number Of Circuits: 1
• Ratio - Input:output: 2:1
• Differential - Input:output: Yes/No
• Frequency - Max: 3.5GHz
• Divider/multiplier: Yes/Yes
• Voltage - Supply: 2.7 V ~ 3.3 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 32-LFCSP
• Frequency-max: 3.5GHz
• Pll Type: Frequency Synthesis
• Frequency: 3.5GHz
• Supply Current: 24mA
• Supply Voltage Range: 2.7V To 3.3V
• Digital Ic Case Style: LFCSP
• No. Of Pins: 32
• Operating Temperature Range: -40°C To +85°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADF4193EBZ2 - BOARD EVALUATION EB2 FOR ADF4193EVAL-ADF4193EBZ1 - BOARD EVALUATION EB1 FOR ADF4193
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

INTERFACING
The ADF4193 has a simple SPI®-compatible serial interface for
writing to the device. CLK, DATA, and LE control the data
transfer. When LE goes high, the 24 bits that have been clocked
into the input register on each rising edge of CLK are latched
into the appropriate register. See Figure 2 for the timing
diagram and Table 5 for the register address table.
The maximum allowable serial clock rate is 33 MHz.
ADuC812 Interface
Figure 37 shows the interface between the ADF4193 and the
ADuC812
an 8051 core, this interface can be used with any 8051-based
microcontroller. The MicroConverter is set up for SPI master
mode with CPHA = 0. To initiate the operation, the I/O port
driving LE is brought low. Some registers of the ADF4193
require a 24-bit programming word. This is accomplished by
writing three 8-bit bytes from the MicroConverter to the device.
When the third byte is written, the LE input should be brought
high to complete the transfer.
An I/O port line on the ADuC812 can also be used to detect
lock (MUX
port input).
ADuC812
MicroConverter®. Because the ADuC812 is based on
OUT
I/O PORTS
Figure 37. ADuC812 to ADF4193 Interface
configured as lock detect and polled by the
SCLOCK
MOSI
CLK
DATA
LE
MUX
(LOCK DETECT)
ADF4193
OUT
Rev. C | Page 27 of 28
ADSP-21xx Interface
Figure 38 shows the interface between the ADF4193 and the
ADSP-21xx digital signal processor. The ADF4193 needs a
24-bit serial word for some writes. The easiest way to accom-
plish this using the ADSP-21xx family is to use the autobuffered
transmit mode of operation with alternate framing. This
provides a means for transmitting an entire block of serial data
before an interrupt is generated. Set up the word length for
eight bits and use three memory locations for each 24-bit word.
To program each 24-bit word, store the three 8-bit bytes, enable
the autobuffered mode, and then write to the transmit register
of the DSP. This last operation initiates the autobuffer transfer.
PCB DESIGN GUIDELINES FOR CHIP SCALE
PACKAGE
The lands on the chip scale package (CP-32-3) are rectangular.
The printed circuit board (PCB) pad for these should be 0.1 mm
longer than the package land length and 0.05 mm wider than
the package land width. The land should be centered on the
pad. This ensures that the solder joint size is maximized. The
bottom of the chip scale package has a central thermal pad.
The thermal pad on the PCB should be at least as large as the
exposed pad. On the PCB, there should be a clearance of at least
0.25 mm between the thermal pad and the inner edges of the
pad pattern. This ensures that shorting is avoided.
Thermal vias can be used on the PCB thermal pad to improve
the thermal performance of the package. If vias are used, they
should be incorporated in the thermal pad at 1.2 mm pitch grid.
The via diameter should be between 0.3 mm and 0.33 mm, and
the via barrel should be plated with one ounce copper to plug
the via.
The user should connect the PCB thermal pad to A
ADSP-21xx
Figure 38. ADSP-21xx to ADF4193 Interface
I/O FLAGS
SCLK
TFS
DT
CLK
DATA
LE
MUX
(LOCK DETECT)
ADF4193
OUT
ADF4193
GND
.