AT91SAM9261SB-CU-999 Atmel, AT91SAM9261SB-CU-999 Datasheet - Page 176

• Manufacturer Part Number: AT91SAM9261SB-CU-999
• Description: IC MCU ARM9 ULTRA LP 217LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9261SB-CU-999

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 190MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: DMA, LCD, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: 2-Wire, I2S, SPI, USB
• Maximum Clock Frequency: 190 MHz
• Number Of Programmable I/os: 96
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9261-EK
• Minimum Operating Temperature: - 40 C
• For Use With: AT91SAM9261-EK - KIT EVAL FOR AT91SAM926EJ-SAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

22.8.6
22.8.7
22.9
22.9.1
176
Automatic Wait States
AT91SAM9261S
Reset Values of Timing Parameters
Usage Restriction
Chip Select Wait States
Table 22-5
Table 22-5.
The SMC does not check the validity of the user-programmed parameters. If the sum of SETUP
and PULSE parameters is larger than the corresponding CYCLE parameter, this leads to unpre-
dictable behavior of the SMC.
For read operations:
Null but positive setup and hold of address and NRD and/or NCS can not be guaranteed at the
memory interface because of the propagation delay of theses signals through external logic and
pads. If positive setup and hold values must be verified, then it is strictly recommended to pro-
gram non-null values so as to cover possible skews between address, NCS and NRD signals.
For write operations:
If a null hold value is programmed on NWE, the SMC can guarantee a positive hold of address,
byte select lines, and NCS signal after the rising edge of NWE. This is true for WRITE_MODE =
1 only. See
For read and write operations: a null value for pulse parameters is forbidden and may lead to
unpredictable behavior.
In read and write cycles, the setup and hold time parameters are defined in reference to the
address bus. For external devices that require setup and hold time between NCS and NRD sig-
nals (read), or between NCS and NWE signals (write), these setup and hold times must be
converted into setup and hold times in reference to the address bus.
Under certain circumstances, the SMC automatically inserts idle cycles between accesses to
avoid bus contention or operation conflict.
The SMC always inserts an idle cycle between 2 transfers on separate chip selects. This idle
cycle ensures that there is no bus contention between the de-activation of one device and the
activation of the next one.
During chip select wait state, all control lines are turned inactive: NBS0 to NBS3, NWR0 to
NWR3, NCS[0..7], NRD lines are all set to 1.
Figure 22-16
Select 2.
Register
SMC_SETUP
SMC_PULSE
SMC_CYCLE
WRITE_MODE
READ_MODE
gives the default value of timing parameters at reset.
“Early Read Wait State” on page
illustrates a chip select wait state between access on Chip Select 0 and Chip
Reset Values of Timing Parameters
Reset Value
0x01010101
0x00010001
0
1
1
All setup timings are set to 1
All pulse timings are set to 1
The read and write operation last 3 Master Clock cycles
and provide one hold cycle
Write is controlled with NWE
Read is controlled with NRD
177.
6242E–ATARM–11-Sep09