MC9S08SH4CTG Freescale, MC9S08SH4CTG Datasheet - Page 118

• Manufacturer Part Number: MC9S08SH4CTG
• Manufacturer: Freescale

Specifications of MC9S08SH4CTG

• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 256Byte
• # I/os (max): 13
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: TSSOP
• Program Memory Type: Flash
• Program Memory Size: 4KB
• Lead Free Status / RoHS Status: Compliant

Chapter 8 Analog Comparator (S08ACMPV2)
8.3.1.1
ACMPSC contains the status flag and control bits which are used to enable and configure the ACMP.
118
ACMOD
ACBGS
ACOPE
ACME
Field
ACIE
ACO
ACF
1:0
7
6
5
4
3
2
Reset:
W
R
Analog Comparator Module Enable — ACME enables the ACMP module.
0 ACMP not enabled
1 ACMP is enabled
Analog Comparator Bandgap Select — ACBGS is used to select between the bandgap reference voltage or
the ACMP+ pin as the input to the non-inverting input of the analog comparatorr.
0 External pin ACMP+ selected as non-inverting input to comparator
1 Internal reference select as non-inverting input to comparator
Note: refer to this chapter introduction to verify if any other config bits are necessary to enable the bandgap
Analog Comparator Flag — ACF is set when a compare event occurs. Compare events are defined by ACMOD.
ACF is cleared by writing a one to ACF.
0 Compare event has not occured
1 Compare event has occured
Analog Comparator Interrupt Enable — ACIE enables the interrupt from the ACMP. When ACIE is set, an
interupt will be asserted when ACF is set.
0 Interrupt disabled
1 Interrupt enabled
Analog Comparator Output — Reading ACO will return the current value of the analog comparator output. ACO
is reset to a 0 and will read as a 0 when the ACMP is disabled (ACME = 0).
Analog Comparator Output Pin Enable — ACOPE is used to enable the comparator output to be placed onto
the external pin, ACMPO.
0 Analog comparator output not available on ACMPO
1 Analog comparator output is driven out on ACMPO
Analog Comparator Mode — ACMOD selects the type of compare event which sets ACF.
00 Encoding 0 — Comparator output falling edge
01 Encoding 1 — Comparator output rising edge
10 Encoding 2 — Comparator output falling edge
11 Encoding 3 — Comparator output rising or falling edge
ACMP Status and Control Register (ACMPSC)
reference in the chip level.
ACME
0
7
Table 8-2. ACMP Status and Control Register Field Descriptions
= Unimplemented
ACBGS
0
6
Figure 8-3. ACMP Status and Control Register
MC9S08SH8 MCU Series Data Sheet, Rev. 3
ACF
5
0
ACIE
0
4
Description
ACO
0
3
ACOPE
0
2
0
1
Freescale Semiconductor
ACMOD
0
0