ATA6613P-PLPW Atmel, ATA6613P-PLPW Datasheet - Page 73

MCU W/LIN TXRX REG WTCHDG 48-QFN

ATA6613P-PLPW

Manufacturer Part Number
ATA6613P-PLPW
Description
MCU W/LIN TXRX REG WTCHDG 48-QFN
Manufacturer
Atmel
Series
AVR® ATA66 LIN-SBCr
Datasheet

Specifications of ATA6613P-PLPW

Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
I²C, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
23
Program Memory Size
16KB (16K x 8)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
48-QFN Exposed Pad
Processor Series
ATA6x
Core
AVR8
Data Bus Width
8 bit
Data Ram Size
1 KB
Interface Type
SPI, TWI, USART
Maximum Clock Frequency
16 MHz
Number Of Programmable I/os
23
Number Of Timers
3
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 8 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
6.8.7
6.8.8
6.8.8.1
9111H–AUTO–01/11
MCU Status Register – MCUSR
Internal Voltage Reference
Voltage Reference Enable Signals and Start-up Time
The MCU Status Register provides information on which reset source caused an MCU reset.
Atmel ATA6612/ATA6613 features an internal bandgap reference. This reference is used for
Brown-out Detection, and it can be used as an input to the Analog Comparator or the ADC.
The voltage reference has a start-up time that may influence the way it should be used. The
start-up time is given in
turned on. The reference is on during the following situations:
Thus, when the BOD is not enabled, after setting the ACBG bit or enabling the ADC, the user
must always allow the reference to start up before the output from the Analog Comparator or
ADC is used. To reduce power consumption in Power-down mode, the user can avoid the
three conditions above to ensure that the reference is turned off before entering Power-down
mode.
• Bit 7..4: Res: Reserved Bits
• Bit 3 – WDRF: Watchdog System Reset Flag
• Bit 2 – BORF: Brown-out Reset Flag
• Bit 1 – EXTRF: External Reset Flag
• Bit 0 – PORF: Power-on Reset Flag
1. When the BOD is enabled (by programming the BODLEVEL [2..0] Fuses).
2. When the bandgap reference is connected to the Analog Comparator (by setting the
3. When the ADC is enabled.
Initial Value
Read/Write
These bits are unused bits in the Atmel
zero.
This bit is set if a Watchdog System Reset occurs. The bit is reset by a Power-on Reset,
or by writing a logic zero to the flag.
This bit is set if a Brown-out Reset occurs. The bit is reset by a Power-on Reset, or by writ-
ing a logic zero to the flag.
This bit is set if an External Reset occurs. The bit is reset by a Power-on Reset, or by writ-
ing a logic zero to the flag.
This bit is set if a Power-on Reset occurs. The bit is reset only by writing a logic zero to the
flag.
To make use of the Reset Flags to identify a reset condition, the user should read and
then Reset the MCUSR as early as possible in the program. If the register is cleared
before another reset occurs, the source of the reset can be found by examining the Reset
Flags.
Bit
ACBG bit in ACSR).
R
7
0
Table 6-23 on page
R
6
0
R
5
0
R
4
0
®
Atmel ATA6612/ATA6613
74. To save power, the reference is not always
ATA6612/ATA6613, and will always read as
WDRF
R/W
3
See Bit Description
BORF
R/W
2
EXTRF
R/W
1
PORF
R/W
0
MCUSR
73

Related parts for ATA6613P-PLPW