ATA6613P-PLPW Atmel, ATA6613P-PLPW Datasheet - Page 319

• Manufacturer Part Number: ATA6613P-PLPW
• Description: MCU W/LIN TXRX REG WTCHDG 48-QFN
• Manufacturer: Atmel
• Series: AVR® ATA66 LIN-SBCr

Specifications of ATA6613P-PLPW

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-QFN Exposed Pad
• Processor Series: ATA6x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 6-128. Serial Programming Instruction Set (Continued)
Note:
6.24.8.4
9111H–AUTO–01/11
Instruction
Read Lock bits
Write Lock bits
Read Signature Byte
Write Fuse bits
Write Fuse High bits
Write Extended Fuse Bits
Read Fuse bits
Read Fuse High bits
Read Extended Fuse Bits
Read Calibration Byte
Poll RDY/BSY
a = address high bits, b = address low bits, H = 0 - Low byte, 1 - High Byte, o = data out, i = data in, x = do not care
SPI Serial Programming Characteristics
For characteristics of the SPI module see
0101 1000
1010 1100
0011 0000
1010 1100
1010 1100
1010 1100
0101 0000
0101 1000
0101 0000
0011 1000
1111 0000
Byte 1
0000 0000
111x xxxx
000x xxxx
1010 0000
1010 1000
1010 0100
0000 0000
0000 1000
0000 1000
000x xxxx
0000 0000
Byte 2
Instruction Format
xxxx xxxx
xxxx xxxx
xxxx xxbb
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
0000 0000
xxxx xxxx
Byte 3
“SPI Timing Characteristics” on page
xxoo oooo Read Lock bits. “0” = programmed, “1” =
11ii iiii Write Lock bits. Set bits = “0” to program
oooo oooo Read Signature Byte o at address b.
iiii iiii Set bits = “0” to program, “1” to
iiii iiii Set bits = “0” to program, “1” to
xxxx xxii Set bits = “0” to program, “1” to
oooo oooo Read Fuse bits. “0” = programmed, “1” =
oooo oooo Read Fuse High bits. “0” = programmed,
oooo oooo Read Extended Fuse bits. “0” =
oooo oooo Read Calibration Byte
xxxx xxxo If o = “1”, a programming operation is still
Atmel ATA6612/ATA6613
Byte4
Operation
unprogrammed. See
page 300
Lock bits. See
for details.
unprogram. See Table XXX on page
XXX for details.
unprogram. See
for details.
unprogram. See
302
unprogrammed. See Table XXX on page
XXX for details.
“1” = unprogrammed. See
page 270
programmed, “1” = unprogrammed. See
Table 6-116 on page 302
busy. Wait until this bit returns to “0”
before applying another command.
for details.
for details.
for details.
Table 6-113 on page 300
Table 6-97 on page 270
Table 6-116 on page
Table 6-113 on
326.
for details.
Table 6-97 on
319