DV164136 Microchip Technology, DV164136 Datasheet - Page 275

• Manufacturer Part Number: DV164136
• Description: DEVELOPMENT KIT FOR PIC18
• Manufacturer: Microchip Technology
• Series: PIC®r
• Type: MCUr

Specifications of DV164136

• Contents: Board, Cables, CDs, PICkit™ 3 Programmer, Power Supply
• Processor To Be Evaluated: PIC18F8722, PIC18F87J11
• Interface Type: RS-232, USB
• Operating Supply Voltage: 3.3 V, 5 V
• Silicon Manufacturer: Microchip
• Core Architecture: PIC
• Core Sub-architecture: PIC18
• Silicon Core Number: PIC18F
• Silicon Family Name: PIC18F8xxx
• Kit Contents: PIC18 Exp Brd PICkit 3 Cable CD PSU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: PIC18F8722, PIC18F87J11
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

20.1
The BRG is a dedicated, 8-bit or 16-bit generator that
supports both the Asynchronous and Synchronous
modes of the EUSART. By default, the BRG operates
in 8-bit mode; setting the BRG16 bit (BAUDCONx<3>)
selects 16-bit mode.
The SPBRGHx:SPBRGx register pair controls the period
of a free-running timer. In Asynchronous mode, bits
BRGH (TXSTAx<2>) and BRG16 (BAUDCONx<3>) also
control the baud rate. In Synchronous mode, BRGH is
ignored. Table 20-1 shows the formula for computation of
the baud rate for different EUSART modes which only
apply in Master mode (internally generated clock).
Given the desired baud rate and F
integer value for the SPBRGHx:SPBRGx registers can
be calculated using the formulas in Table 20-1. From this,
the error in baud rate can be determined. An example
calculation is shown in Example 20-1. Typical baud rates
and error values for the various Asynchronous modes
are shown in Table 20-2. It may be advantageous to use
TABLE 20-1:
© 2009 Microchip Technology Inc.
Legend: x = Don’t care, n = value of SPBRGHx:SPBRGx register pair
SYNC
0
0
0
0
1
1
Baud Rate Generator (BRG)
Configuration Bits
BAUD RATE FORMULAS
BRG16
0
0
1
1
0
1
BRGH
0
1
0
1
x
x
OSC
, the nearest
BRG/EUSART Mode
16-bit/Asynchronous
16-bit/Asynchronous
16-bit/Synchronous
8-bit/Asynchronous
8-bit/Asynchronous
8-bit/Synchronous
PIC18F87J11 FAMILY
the high baud rate (BRGH = 1) or the 16-bit BRG to
reduce the baud rate error, or achieve a slow baud rate
for a fast oscillator frequency.
Writing a new value to the SPBRGHx:SPBRGx regis-
ters causes the BRG timer to be reset (or cleared). This
ensures the BRG does not wait for a timer overflow
before outputting the new baud rate.
20.1.1
The device clock is used to generate the desired baud
rate. When one of the power-managed modes is
entered, the new clock source may be operating at a
different frequency. This may require an adjustment to
the value in the SPBRGx register pair.
20.1.2
The data on the RXx pin (either RC7/RX1/DT1 or
RG2/RX2/DT2) is sampled three times by a majority
detect circuit to determine if a high or a low level is
present at the RXx pin.
OPERATION IN POWER-MANAGED
MODES
SAMPLING
Baud Rate Formula
F
F
F
OSC
OSC
OSC
/[64 (n + 1)]
/[16 (n + 1)]
/[4 (n + 1)]
DS39778D-page 275