DV164136 Microchip Technology, DV164136 Datasheet - Page 253

• Manufacturer Part Number: DV164136
• Description: DEVELOPMENT KIT FOR PIC18
• Manufacturer: Microchip Technology
• Series: PIC®r
• Type: MCUr

Specifications of DV164136

• Contents: Board, Cables, CDs, PICkit™ 3 Programmer, Power Supply
• Processor To Be Evaluated: PIC18F8722, PIC18F87J11
• Interface Type: RS-232, USB
• Operating Supply Voltage: 3.3 V, 5 V
• Silicon Manufacturer: Microchip
• Core Architecture: PIC
• Core Sub-architecture: PIC18
• Silicon Core Number: PIC18F
• Silicon Family Name: PIC18F8xxx
• Kit Contents: PIC18 Exp Brd PICkit 3 Cable CD PSU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: PIC18F8722, PIC18F87J11
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

19.4.6
Master mode is enabled by setting and clearing the
appropriate SSPM bits in SSPxCON1 and by setting
the SSPEN bit. In Master mode, the SCLx and SDAx
lines are manipulated by the MSSP hardware if the
TRIS bits are set.
Master mode of operation is supported by interrupt
generation on the detection of the Start and Stop
conditions. The Stop (P) and Start (S) bits are cleared
from a Reset or when the MSSP module is disabled.
Control of the I
set, or the bus is Idle, with both the S and P bits clear.
In Firmware Controlled Master mode, user code
conducts all I
Stop bit conditions.
Once Master mode is enabled, the user has six
options.
1.
2.
3.
4.
5.
6.
FIGURE 19-18:
© 2009 Microchip Technology Inc.
SDAx
SCLx
Assert a Start condition on SDAx and SCLx.
Assert a Repeated Start condition on SDAx and
SCLx.
Write to the SSPxBUF register initiating
transmission of data/address.
Configure the I
Generate an Acknowledge condition at the end
of a received byte of data.
Generate a Stop condition on SDAx and SCLx.
MASTER MODE
2
C bus operations based on Start and
2
C bus may be taken when the P bit is
2
C port to receive data.
MSSP BLOCK DIAGRAM (I
SDAx In
Bus Collision
SCLx In
Read
MSb
Write Collision Detect
End of XMIT/RCV
Start bit, Stop bit,
State Counter for
Clock Arbitration
Acknowledge
Stop bit Detect
Start bit Detect
SSPxBUF
SSPxSR
Generate
2
C™ MASTER MODE)
LSb
PIC18F87J11 FAMILY
Write
The following events will cause the MSSP Interrupt
Flag bit, SSPxIF, to be set (and MSSP interrupt, if
enabled):
• Start condition
• Stop condition
• Data transfer byte transmitted/received
• Acknowledge transmitted
• Repeated Start
Clock
Data Bus
Shift
Internal
Note:
Set/Reset S, P (SSPxSTAT), WCOL (SSPxCON1);
Set SSPxIF, BCLxIF;
Reset ACKSTAT, PEN (SSPxCON2)
The MSSP module, when configured in
I
of events. For instance, the user is not
allowed to initiate a Start condition and
immediately write the SSPxBUF register to
initiate transmission before the Start
condition is complete. In this case, the
SSPxBUF will not be written to and the
WCOL bit will be set, indicating that a write
to the SSPxBUF did not occur.
2
C Master mode, does not allow queueing
SSPM3:SSPM0
SSPxADD<6:0>
Generator
Baud
Rate
DS39778D-page 253