S25FL128SAGMFI011 Spansion, S25FL128SAGMFI011 Datasheet - Page 127
S25FL128SAGMFI011
Manufacturer Part Number
S25FL128SAGMFI011
Description
Flash 128Mb 3V 133MHz Serial NOR Flash
Manufacturer
Spansion
Datasheet
1.S25FL128SAGNFI001.pdf
(153 pages)
Specifications of S25FL128SAGMFI011
Rohs
yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
S25FL128SAGMFI011
Manufacturer:
SPANSION
Quantity:
20 000
- Current page: 127 of 153
- Download datasheet (6Mb)
July 12, 2012 S25FL128S_256S_00_05
10.8.11
SCK
CS#
SO
SI
Password Program (PASSP E8h)
Before the Password Program (PASSP) command can be accepted by the device, a Write Enable (WREN)
command must be issued and decoded by the device. After the Write Enable (WREN) command has been
decoded, the device sets the Write Enable Latch (WEL) to enable the PASSP operation.
The password can only be programmed before the Password Mode is selected by programming the
Password Protection Mode bit to 0 in the ASP Register (ASP[2]). After the Password Protection Mode is
selected the PASSP command is ignored.
The PASSP command is entered by driving CS# to the logic low state, followed by the instruction and the
password data bytes on SI, least significant byte first, most significant bit of each byte first. The password is
sixty-four (64) bits in length.
CS# must be driven to the logic high state after the sixty-fourth (64
PASSP command is not executed. As soon as CS# is driven to the logic high state, the self-timed PASSP
operation is initiated. While the PASSP operation is in progress, the Status Register may be read to check the
value of the Write-In Progress (WIP) bit. The Write-In Progress (WIP) bit is a 1 during the self-timed PASSP
cycle, and is a 0 when it is completed. The PASSP command can report a program error in the P_ERR bit of
the status register. When the PASSP operation is completed, the Write Enable Latch (WEL) is set to a 0. The
maximum clock frequency for the PASSP command is 133 MHz.
MSB
7
0
CS#
SCK
SO
SI
6
1
Figure 10.80 Password Program Command Sequence
5
2
High Impedance
Instruction
4
D a t a
3
Figure 10.79 Password Read Command Sequence
MSB
7
3
0
S25FL128S and S25FL256S
4
6
1
S h e e t
2
5
5
2
High Impedance
Instruction
1
4
3
6
3
4
0
7
2
5
MSB
7
1
6
8
0
7
6
MSB
9
7
8
Password Least Sig. Byte First
5
6
10
9
th
Password
5
10
) bit of data has been latched. If not, the
4
11
59
68
58
58
69
69
57
70
57
56
70
71
MSB
7
56
72
71
127
Related parts for S25FL128SAGMFI011
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
MBM29F400TC-70PFTNSPANSION [FLASH MEMORY CMOS 4M (512K x 8/256K x 16) BIT]
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
AM29F010B70JI1 Megabit (128 K x 8-bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016D70BAI02016 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI01016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI02016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet: