LPC47S457-NC SMSC [SMSC Corporation], LPC47S457-NC Datasheet - Page 106
![no-image](/images/no-image-200.jpg)
LPC47S457-NC
Manufacturer Part Number
LPC47S457-NC
Description
Advanced I/O with X-Bus Interface
Manufacturer
SMSC [SMSC Corporation]
Datasheet
1.LPC47S457-NC.pdf
(259 pages)
- Current page: 106 of 259
- Download datasheet (2Mb)
2.
An SER_IRQ mode transition can only occur during the Stop Frame. Upon reset, SER_IRQ bus is defaulted to
Continuous mode, therefore only the Host controller can initiate the first Start Frame.
continuously sample the Stop Frames pulse width to determine the next SER_IRQ Cycle’s mode.
SER_IRQ Data Frame
Once a Start Frame has been initiated, the LPC47S45x will watch for the rising edge of the Start Pulse and start
counting IRQ/Data Frames from there. Each IRQ/Data Frame is three clocks: Sample phase, Recovery phase, and
Turn-around phase. During the Sample phase the LPC47S45x drives the SER_IRQ low, if and only if, its last
detected IRQ/Data value was low. If its detected IRQ/Data value is high, SER_IRQ is left tri-stated. During the
Recovery phase the LPC47S45x drives the SER_IRQ high, if and only if, it had driven the SER_IRQ low during the
previous Sample Phase. During the Turn-around Phase the LPC47S45x tri-states the SER_IRQ. The LPC47S45x
will drive the SER_IRQ line low at the appropriate sample point if its associated IRQ/Data line is low, regardless of
which device initiated the Start Frame.
The Sample Phase for each IRQ/Data follows the low to high transition of the Start Frame pulse by a number of
clocks equal to the IRQ/Data Frame times three, minus one. (e.g. The IRQ5 Sample clock is the sixth IRQ/Data
Frame, (6 x 3) - 1 = 17th clock after the rising edge of the Start Pulse).
The SER_IRQ data frame will now supports IRQ2 from a logical device on Period 3, which can also be used for the
System Management Interrupt (nSMI). When using Period 3 for IRQ2 the user should mask off the SMI via the SMI
Enable Register. Likewise, when using Period 3 for nSMI the user should not configure any logical devices as using
IRQ2.
SER_IRQ Period 14 is used to transfer IRQ13. Logical devices 0 (FDC), 3 (Par Port), 4 (Ser Port 1), 5 (Ser Port 2)
and 7 (KBD) shall have IRQ13 as a choice for their primary interrupt. The polarity of IRQ8 is programmable via bit 0
of register 0xF1 in Logical Device A.
The SMI is enabled onto the SMI frame of the Serial IRQ via bit 6 of SMI Enable Register 2 and onto the SMI pin via
bit 7 of the SMI Enable Register 2.
Stop Cycle Control
SMSC DS – LPC47S45x
Continuous (Idle) Mode: Only the Host controller can initiate a Start Frame to update IRQ/Data line information.
All other SER_IRQ agents become passive and may not initiate a Start Frame. SER_IRQ will be driven low for
four to eight clocks by Host Controller. This mode has two functions. It can be used to stop or idle the SER_IRQ
or the Host Controller can operate SER_IRQ in a continuous mode by initiating a Start Frame at the end of every
Stop Frame.
SER_IRQ PERIOD
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
SER_IRQ Sampling Periods
DATASHEET
SIGNAL SAMPLED
nIO_SMI/IRQ2
Not Used
Page 106 of 259
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
IRQ1
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ9
# OF CLOCKS PAST START
11
14
17
20
23
26
29
32
35
38
41
44
47
2
5
8
Slaves must
Rev. 07/09/2001
Related parts for LPC47S457-NC
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LAN83C183-JD](/images/no-image3.png)
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N769TQFP](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47M102S-MC](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47N267-MN](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![USB20H04-JD](/images/no-image3.png)
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37M602](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37B777](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37C672](/images/no-image3.png)
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
![COM90C66LJP](/images/no-image3.png)
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N869TQFP](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![USB97C100QFP](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47N227-MN](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N869](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![LAN91C94](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: