LAN9420I-NU Standard Microsystems (SMSC), LAN9420I-NU Datasheet - Page 41

• Manufacturer Part Number: LAN9420I-NU
• Manufacturer: Standard Microsystems (SMSC)

Specifications of LAN9420I-NU

• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 128
• Lead Free Status / RoHS Status: Compliant

Single-Chip Ethernet Controller with HP Auto-MDIX Support and PCI Interface
Datasheet
SMSC LAN9420/LAN9420i
RDES0
RDES2
RDES3
3.4.2.1
RDES1
BITS
31
30
OW
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Receive Descriptors
The receive descriptors must be 4-DWORD (16-byte) aligned. Except for the case where descriptor
address chaining is disabled (RCH=0), there are no alignment restrictions on receive buffer addresses.
Providing two buffers, two byte-count buffers, and two address pointers in each descriptor facilitates
compatibility with various types of memory-management schemes.
descriptor.
Receive Descriptor 0 (RDES0)
RDES0 contains the received frame status, the frame length, and the descriptor ownership information.
FF
RESERVED
OWN - Own Bit
When set, indicates that the descriptor block and associated buffer(s) are owned by the DMA
controller. When reset, indicates that the descriptor block and associated buffer(s) are owned by
the Host system.
Host Actions: Checks this bit to determine ownership of the descriptor block and associated
buffer(s). The Host sets this bit to pass ownership to the DMAC. The Host does not modify a
descriptor block or access its associated buffer(s) until this bit is cleared by DMAC or until the
DMAC is in STOPPED state, whichever comes first.
DMAC Actions: Reads this bit to determine ownership of the descriptor block and its associated
buffer(s). The DMAC clears this bit either when it completes the frame reception or when the
buffers that are associated with this descriptor are full. By clearing this bit, the DMAC closes the
descriptor block and passes ownership to the Host. If the DMAC fetches a descriptor with the
OWN bit cleared, the DMAC state machine enters the SUSPENDED state.
FF - Filter Fail
Indicates that the current frame failed the receive address filtering. This bit can only be set when
receive all (RXALL) is set in the MAC control register (MAC_CR). This bit is only valid when the
last descriptor (LS) bit is set and the received frame is greater than or equal to 64 bytes in length.
Host Actions: Checks this bit to determine status.
DMAC Actions: Sets/clears this bit to define status.
RE RC RES
FL
Figure 3.16 Receive Descriptor
Table 3.5 RDES0 Bit Fields
DATASHEET
BUFFER 1 ADDRESS POINTER
BUFFER 2 ADDRESS POINTER
41
DESCRIPTION
RBS2
ES DE
R
LE RF MF FS LS TL CS FT RW ME DB CE R
Figure 3.16
RBS1
Revision 1.4 (12-17-08)
shows the receive