LAN9420I-NU Standard Microsystems (SMSC), LAN9420I-NU Datasheet - Page 155

• Manufacturer Part Number: LAN9420I-NU
• Manufacturer: Standard Microsystems (SMSC)

Specifications of LAN9420I-NU

• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 128
• Lead Free Status / RoHS Status: Compliant

Single-Chip Ethernet Controller with HP Auto-MDIX Support and PCI Interface
Datasheet
Chapter 5 Operational Characteristics
SMSC LAN9420/LAN9420i
5.1
5.2
Absolute Maximum Ratings*
Operating Conditions**
Supply Voltage (VDD33A, VDD33BIAS, VDD33IO)
Positive voltage on signal pins, with respect to ground
Negative voltage on signal pins, with respect to ground
Positive voltage on XI, with respect to ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.6V
Positive voltage on XO, with respect to ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.5V
Ambient Operating Temperature in Still Air (T
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55
Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to JEDEC Spec. J-STD-020
HBM ESD Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..+/- 5kV
Note 5.1
Note 5.2
Note 5.3
Note 5.4
*Stresses exceeding those listed in this section could cause permanent damage to the device. This is
a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Functional operation of the device at any condition exceeding those indicated in
Section 5.2, "Operating
of this specification is not implied. Note, device signals are NOT 5 volt tolerant.
Supply Voltage (VDD33A, VDD33BIAS, VDD33IO) . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.3V +/- 300mV
Ambient Operating Temperature in Still Air (T
**Proper operation of LAN9420/LAN9420i is guaranteed only within the ranges specified in this section.
When powering this device from laboratory or system power supplies, it is important that
the absolute maximum ratings not be exceeded or device failure can result. Some power
supplies exhibit voltage spikes on their outputs when AC power is switched on or off. In
addition, voltage transients on the AC power line may appear on the DC output. If this
possibility exists, it is suggested that a clamp circuit be used.
This rating does not apply to the following pins: XI, XO, EXRES.
This rating does not apply to the following pins: EXRES.
0
o
C to +70
o
Conditions**",
C for commercial version, -40
DATASHEET
Section 5.4, "DC
155
A
A
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(Note
o
C to +85
(Note
Specifications", or any other applicable section
(Note
5.1) . . . . . . . . . . . . . . . . . . . . . . 0V to +3.6V
5.2) . . . . . . . . . . . . . . . . . . . . . . . . . . +6V
5.3) . . . . . . . . . . . . . . . . . . . . . . . . -0.5V
o
C for industrial version.
Revision 1.4 (12-17-08)
o
C to +150
Note 5.4
Note 5.4
o
C