IP-CPRI Altera, IP-CPRI Datasheet - Page 144
![no-image](/images/manufacturer_photos/0/0/40/altera_sml.jpg)
IP-CPRI
Manufacturer Part Number
IP-CPRI
Description
IP CORE - Common Public Radio Interface (CPRI)
Manufacturer
Altera
Specifications of IP-CPRI
Software Application
IP CORE, Interface And Protocols, HIGH SPEED
Supported Families
Arria II GX, Cyclone IV GX, HardCopy IV, Stratix IV
Core Architecture
FPGA
Core Sub-architecture
Arria, Cyclone, Stratix
Rohs Compliant
NA
Lead Free Status / RoHS Status
na
Lead Free Status / RoHS Status
na
- Current page: 144 of 150
- Download datasheet (3Mb)
B–4
CPRI MegaCore Function User Guide
2. Set the logic that feeds the gxb_refclk input to the CPRI IP core to the correct
3. Configure the ALTGX_RECONFIG megafunction with the .mif file for the desired
4. For a Cyclone IV GX device, configure the ALTPLL_RECONFIG megafunction
5. Set the i_datarate_set field of the AUTO_RATE_CONFIG register to the correct value
6. Confirm the field is set by monitoring the datarate_set output signal.
7. Optionally, to enable confirmation of frame synchronization at the new CPRI line
8. If you reset the tx_enable bit of the CPRI_CONFIG register in step 7, after
value for the next CPRI line rate at which you want to try to achieve frame
synchronization.
CPRI line rate.
with the .mif file for the desired CPRI line rate, by performing the following steps:
a. Assert the write_from_rom input signal to the ALTPLL_RECONFIG megafunction.
b. After the megafunction busy output signal is deasserted, assert the
c. After the CPRI IP core pll_reconfig_done signal is deasserted, assert the
for the next CPRI line rate at which you want to try to achieve frame
synchronization.
rate, reset the tx_enable bit of the CPRI_CONFIG register to 0.
The frame synchronization machine shown in
to achieve frame synchronization at the specified CPRI line rate.
extended_rx_status_data[1:0] changes value to 0x1, set the tx_enable bit of the
CPRI_CONFIG register.
The value 0x3 on the extended_rx_status_data[1:0] signal confirms that the
CPRI receiver has achieved frame synchronization.
The megafunction busy output signal is asserted and remains asserted while
the megafunction writes to the scan cache.
megafunction reconfig signal. While PLL reconfiguration is in progress, the
busy signal is again asserted.
megafunction reset_rom_address signal.
Appendix B: Implementing CPRI Link Autorate Negotiation
Figure 4–10 on page 4–20
May 2011 Altera Corporation
Running Autorate Negotiation
attempts
Related parts for IP-CPRI
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![IPTR-C2H-NIOS](/images/manufacturer_photos/0/0/40/altera_tmb.jpg)
Part Number:
Description:
IP CORE Renewal Of IPT-C2H-NIOS
Manufacturer:
Altera
Datasheet:
![IP-XAUIPCS](/images/manufacturer_photos/0/0/40/altera_tmb.jpg)
Part Number:
Description:
IP CORE - XAUI PHY
Manufacturer:
Altera
Datasheet:
![IP-RLDRAMII](/images/manufacturer_photos/0/0/40/altera_tmb.jpg)
Part Number:
Description:
IP CORE - RLDRAM II Controller
Manufacturer:
Altera
Datasheet:
![IP-SRAM/QDRII](/images/manufacturer_photos/0/0/40/altera_tmb.jpg)
Part Number:
Description:
IP CORE - QDRII SRAM Controller
Manufacturer:
Altera
Datasheet:
![IP-LINK](/images/no-image3.png)
Part Number:
Description:
MODULE, TX/RX, W/ PSU, IP-LINK
Manufacturer:
TOPCO SNT
Datasheet:
![I2C CONTROLLER IP CORE](/images/no-image3.png)
Part Number:
Description:
I2C Controller FPGA IP Core
Manufacturer:
SYSTEM LEVEL SOLUTIONS
![IP-10GETHERNET](/photos/24/19/241934/4696150_tmb.jpg)
Part Number:
Description:
IP CORE - 10 Gbps Ethernet MAC PCS PMA Reference Design
Manufacturer:
Altera
Datasheet:
![IP-NIOS](/images/manufacturer_photos/0/0/40/altera_tmb.jpg)
Part Number:
Description:
IP NIOS II MEGACORE
Manufacturer:
Altera
Datasheet: