NUC100LC1BN Nuvoton Technology Corporation of America, NUC100LC1BN Datasheet - Page 129

• Manufacturer Part Number: NUC100LC1BN
• Description: IC MCU 32BIT 32KB FLASH 48LQFP
• Manufacturer: Nuvoton Technology Corporation of America
• Series: NuMicro™r

Specifications of NUC100LC1BN

• Core Processor: ARM Cortex-M0
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, I²S, LVD, POR, PS2, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

[4]
[3]
[2:1]
[0]
NuMicro™ NUC100 Series Technical Reference Manual
BOD_INTF
BOD_RSTEN
BOD_VL
BOD_EN
REGWRPROT at address GCR_BA+0x100.
Brown Out Detector Interrupt Flag
1 = When Brown Out Detector detects the VDD is dropped down through the voltage of
BOD_VL setting or the VDD is raised up through the voltage of BOD_VL setting, this
bit is set to 1 and the brown out interrupt is requested if brown out interrupt is enabled.
0 = Brown Out Detector does not detect any voltage draft at VDD down through or up
through the voltage of BOD_VL setting.
Software can write 1 to clear this bit to zero.
Brown Out Reset Enable (write-protection bit)
1 = Enable the Brown Out “RESET” function
While the Brown Out Detector function is enabled (BOD_EN high) and BOD reset
function is enabled (BOD_RSTEN high), BOD will assert a signal to reset chip when
the detected voltage is lower than the threshold (BOD_OUT high).
0 = Enable the Brown Out “INTERRUPT” function
While the BOD function is enabled (BOD_EN high) and BOD interrupt function is
enabled (BOD_RSTEN low), BOD will assert an interrupt if BOD_OUT is high. BOD
interrupt will keep till to the BOD_EN set to 0. BOD interrupt can be blocked by
disabling the NVIC BOD interrupt or disabling BOD function (set BOD_EN low).
The default value is set by flash controller user configuration register config0 bit[20].
This bit is the protected bit. It means programming this needs to write “59h”, “16h”,
“88h” to address 0x5000_0100 to disable register protection. Reference the register
REGWRPROT at address GCR_BA+0x100.
Brown Out Detector Threshold Voltage Selection (write-protection bits)
The default value is set by flash controller user configuration register config0 bit[22:21]
This bit is the protected bit. It means programming this needs to write “59h”, “16h”,
“88h” to address 0x5000_0100 to disable register protection. Reference the register
REGWRPROT at address GCR_BA+0x100.
Brown Out Detector Enable (write-protection bit)
The default value is set by flash controller user configuration register config0 bit[23]
1 = Brown Out Detector function is enabled
0 = Brown Out Detector function is disabled
This bit is the protected bit. It means programming this needs to write “59h”, “16h”,
“88h” to address 0x5000_0100 to disable register protection. Reference the register
REGWRPROT at address GCR_BA+0x100.
BOV_VL[1]
1
1
0
0
- 129 -
BOV_VL[0]
1
0
1
0
Publication Release Date: Oct 22, 2010
Brown out voltage
4.5V
3.8V
2.7V
2.2V
Revision V1.06