DF3048BVX25V Renesas Electronics America, DF3048BVX25V Datasheet - Page 625
DF3048BVX25V
Manufacturer Part Number
DF3048BVX25V
Description
MCU 3/5V 128K PB-FREE 100-TQFP
Manufacturer
Renesas Electronics America
Series
H8® H8/300Hr
Specifications of DF3048BVX25V
Core Processor
H8/300H
Core Size
16-Bit
Speed
25MHz
Connectivity
SCI, SmartCard
Peripherals
DMA, PWM, WDT
Number Of I /o
70
Program Memory Size
128KB (128K x 8)
Program Memory Type
FLASH
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 8x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 75°C
Package / Case
100-TQFP, 100-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DF3048BVX25V
Manufacturer:
Renesas Electronics America
Quantity:
10 000
- Current page: 625 of 903
- Download datasheet (5Mb)
Notes on Using the Boot Mode
1. When this LSI comes out of reset in boot mode, it measures the low period the input at the
2. In boot mode, if any data has been written to the flash memory (if all data is not H'FF), all
3. Interrupts cannot be used during programming or erasing of flash memory.
4.
5. This LSI terminates transmit and receive operations by the on-chip SCI(channel 1) (by clearing
6. Transition to the boot mode executes a reset-start of this LSI after setting the MD
SCI’s RXD
states for this LSI to get ready to measure the low period of the RXD
flash memory blocks are erased. Therefore, this mode should be used for initial on-board
programming, or for forced recovery if the program to be activated in user program mode is
accidentally erased and user program mode cannot be executed, for example.
the RE and TE bits in serial control register (SCR)) before branching to the transmit data
output pin. However, the adjusted bit rate is held in the bit rate register (BRR). At this time, the
TXD
Before branching to the programming control program the value of the general registers in the
CPU are also undefined. Therefore, the general registers must be initialized immediately after
control branches to the programming control program. Since the stack pointer (SP) is
implicitly used during subroutine call, etc., a stack area must be specified for use by the
programming control program.
There are no other internal I/O registers in which the initial value is changed.
FWE, and RXD1 pins according to the mode setting conditions shown in table 18.6.
At this time, this LSI latches the status of the mode pin inside the microcomputer to maintain
the boot mode status at the reset clear (startup from Low level to High level) timing *
To clear boot mode, it is necessary to drive the FWE pin low during the reset, and then execute
reset release *
•
•
The RXD
Before making a transition from the boot mode to the regular mode, the microcomputer
boot mode must be reset by reset input via the RES pin *
hold at low level for at least 20 system clock *
Do not change the input levels at the mode pins (MD
boot mode. When making a mode transition, first enter the reset state by inputting a low
level to the RES pin. When a watchdog timer reset was generated in the boot mode, the
microcomputer mode is not reset and the on-chip boot program is restarted regardless of
the state of the mode pin.
1
is in the high level output state (P9DDR P9
Section 18 ROM (H8/3048F-ONE: Single Power Supply, H8/3048B Mask ROM Version)
1
1
and TXD
pin. The reset should end with RXD
1
. The following points must be noted:
1
pins should be pulled up on the board.
1
2
1
.
high. After the reset ends, it takes about 100
DDR=1, P9DR P9
Rev. 3.00 Sep 27, 2006 page 597 of 872
2
to MD
1
. At this time, the RES pin must be
0
) or the FWE pin while in
1
1
DR=1).
input.
REJ09B0325-0300
0
to MD
1
.
2
,
Related parts for DF3048BVX25V
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: