PIC18C658-I/L Microchip Technology, PIC18C658-I/L Datasheet - Page 144

• Manufacturer Part Number: PIC18C658-I/L
• Description: IC PIC MCU OTP 16KX16 68PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C658-I/L

• Core Size: 8-Bit
• Program Memory Size: 32KB (16K x 16)
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Number Of I /o: 52
• Program Memory Type: OTP
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 68-PLCC
• Controller Family/series: PIC18
• No. Of I/o's: 52
• Ram Memory Size: 1.5KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1536 B
• Interface Type: 3-Wire, I2C, SPI, USART, CAN
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 52
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: ICE2000, DM163007, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164308 - MODULE SKT FOR PM3 68PLCCDVA18PQ640 - DEVICE ADAPT PIC18C658 64-TQFPAC174007 - MODULE SKT PROMATEII 68PLCC
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC18C658IL; Q1162292

PIC18CXX8
15.3.4
In Slave mode, the data is transmitted and received as
the external clock pulses appear on SCK. When the
last bit is latched, the SSPIF interrupt flag bit is set.
While in Slave mode, the external clock is supplied by
the external clock source on the SCK pin. This external
clock must meet the minimum high and low times, as
specified in the electrical specifications.
While in SLEEP mode, the slave can transmit/receive
data. When a byte is received, the device will wake-up
from SLEEP.
15.3.5
The SS pin allows a Synchronous Slave mode. The
SPI must be in Slave mode with SS pin control
enabled (SSPCON1<3:0> = 04h). The pin must not
be driven low for the SS pin to function as an input.
The Data Latch must be high. When the SS pin is
low, transmission and reception are enabled and
the SDO pin is driven. When the SS pin goes high,
FIGURE 15-3: SLAVE SYNCHRONIZATION WAVEFORM
DS30475A-page 144
SS
SCK
(CKP = 0
CKE = 0)
SCK
(CKP = 1
CKE = 0)
Write to
SSPBUF
SDO
SDI
(SMP = 0)
Input
Sample
(SMP = 0)
SSPIF
SSPSR to
SSPBUF
SLAVE MODE
SLAVE SELECT SYNCHRONIZATION
bit7
bit7
bit6
Advanced Information
the SDO pin is no longer driven, even if in the mid-
dle of a transmitted byte, and becomes a floating
output. External pull-up/pull-down resistors may be
desirable, depending on the application.
When the SPI module resets, the bit counter is forced
to 0. This can be done by either forcing the SS pin to a
high level, or clearing the SSPEN bit.
To emulate two-wire communication, the SDO pin can
be connected to the SDI pin. When the SPI needs to
operate as a receiver, the SDO pin can be configured
as an input. This disables transmissions from the SDO.
The SDI can always be left as an input (SDI function),
since it cannot create a bus conflict.
Note 1: When the SPI is in Slave mode with SS pin
2: If the SPI is used in Slave mode with CKE
control enabled, (SSPCON<3:0> = 0100)
the SPI module will reset if the SS pin is
set to V
set, then the SS pin control must be
enabled.
bit7
bit7
DD
.
 2000 Microchip Technology Inc.
Next Q4 Cycle
after Q2 ↓
bit0
bit0