PIC12F675T-I/SN Microchip Technology, PIC12F675T-I/SN Datasheet - Page 58

no-image

PIC12F675T-I/SN

Manufacturer Part Number
PIC12F675T-I/SN
Description
IC MCU CMOS 1K FLASH W/AD 8-SOIC
Manufacturer
Microchip Technology
Series
PIC® 12Fr

Specifications of PIC12F675T-I/SN

Core Size
8-Bit
Program Memory Size
1.75KB (1K x 14)
Core Processor
PIC
Speed
20MHz
Peripherals
POR, WDT
Number Of I /o
5
Program Memory Type
FLASH
Eeprom Size
128 x 8
Ram Size
64 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 4x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Controller Family/series
PIC12
No. Of I/o's
6
Eeprom Memory Size
128Byte
Ram Memory Size
64Byte
Cpu Speed
20MHz
No. Of Timers
2
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Connectivity
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
PIC12F675-I/SNTR
PIC12F675-I/SNTR
PIC12F675T-I/SN
PIC12F675T-I/SNTR
Q1324216

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC12F675T-I/SN
Manufacturer:
MICROCHIP
Quantity:
44 520
Part Number:
PIC12F675T-I/SN
Manufacturer:
MICROCHIPS-PB
Quantity:
3 170
PIC12F629/675
9.3.1
PIC12F629/675 devices have a noise filter in the
MCLR Reset path. The filter will detect and ignore
small pulses.
It should be noted that a WDT Reset does not drive
MCLR pin low.
The behavior of the ESD protection on the MCLR pin
has been altered from previous devices of this family.
Voltages applied to the pin that exceed its specification
can result in both MCLR Resets and excessive current
beyond the device specification during the ESD event.
For this reason, Microchip recommends that the MCLR
pin no longer be tied directly to V
network, as shown in Figure 9-5, is suggested.
An internal MCLR option is enabled by setting the
MCLRE bit in the Configuration Word. When enabled,
MCLR is internally tied to V
option is available for the MCLR pin.
FIGURE 9-5:
9.3.2
The on-chip POR circuit holds the chip in Reset until
V
operation. To take advantage of the POR, simply tie the
MCLR pin through a resistor to V
external RC components usually needed to create
Power-on Reset. A maximum rise time for V
required. See Electrical Specifications for details (see
Section 12.0 “Electrical Specifications”). If the BOD
is enabled, the maximum rise time specification does
not apply. The BOD circuitry will keep the device in
Reset until V
“Brown-Out Detect (BOD)”).
When the device starts normal operation (exits the
Reset condition), device operating parameters (i.e.,
voltage, frequency, temperature, etc.) must be met to
ensure operation. If these conditions are not met, the
device must be held in Reset until the operating
conditions are met.
DS41190G-page 58
DD
Note:
has reached a high enough level for proper
V
DD
R1
1 kor greater
C1
0.1
(optional, not critical)
The POR circuit does not produce an
internal Reset when V
MCLR
POWER-ON RESET (POR)
DD
f
reaches V
RECOMMENDED
CIRCUIT
BOD
DD
DD
DD
. No internal pull-up
MCLR
DD
(see Section 9.3.5
PIC12F629/675
. The use of an RC
. This will eliminate
declines.
MCLR
DD
is
For additional information, refer to Application Note
AN607, “Power-up Trouble Shooting”.
9.3.3
The Power-up Timer provides a fixed 72 ms (nominal)
time-out on power-up only, from POR or Brown-out
Detect. The Power-up Timer operates on an internal
RC oscillator. The chip is kept in Reset as long as
PWRT is active. The PWRT delay allows the V
rise to an acceptable level. A Configuration bit, PWRTE
can disable (if set) or enable (if cleared or
programmed) the Power-up Timer. The Power-up
Timer should always be enabled when Brown-out
Detect is enabled.
The Power-up Time delay will vary from chip to chip
and due to:
• V
• Temperature variation
• Process variation.
See DC parameters for details (Section 12.0 “Electri-
cal Specifications”).
9.3.4
The Oscillator Start-up Timer (OST) provides a 1024
oscillator cycle (from OSC1 input) delay after the
PWRT delay is over. This ensures that the crystal
oscillator or resonator has started and stabilized.
The OST time-out is invoked only for XT, LP and HS
modes and only on Power-on Reset or wake-up from
Sleep.
DD
variation
POWER-UP TIMER (PWRT)
OSCILLATOR START-UP TIMER
(OST)
 2010 Microchip Technology Inc.
DD
to

Related parts for PIC12F675T-I/SN