PIC12F675T-I/SN Microchip Technology, PIC12F675T-I/SN Datasheet - Page 43

• Manufacturer Part Number: PIC12F675T-I/SN
• Description: IC MCU CMOS 1K FLASH W/AD 8-SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12F675T-I/SN

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Controller Family/series: PIC12
• No. Of I/o's: 6
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 64Byte
• Cpu Speed: 20MHz
• No. Of Timers: 2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Connectivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: PIC12F675-I/SNTR; PIC12F675-I/SNTR; PIC12F675T-I/SN; PIC12F675T-I/SNTR; Q1324216

7.0
The
conversion of an analog input signal to a 10-bit binary
representation of that signal. The PIC12F675 has four
analog inputs, multiplexed into one sample and hold
FIGURE 7-1:
7.1
There are two registers available to control the
functionality of the A/D module:
1.
2.
7.1.1
The ANS3:ANS0 bits (ANSEL<3:0>) and the TRISIO
bits control the operation of the A/D port pins. Set the
corresponding TRISIO bits to set the pin output driver
to its high-impedance state. Likewise, set the
corresponding ANS bit to disable the digital input
buffer.
7.1.2
There are four analog channels on the PIC12F675,
AN0
(ADCON0<3:2>) control which channel is connected to
the sample and hold circuit.
7.1.3
There are two options for the voltage reference to the
A/D converter: either V
applied to V
 2010 Microchip Technology Inc.
Note:
ADCON0 (Register 7-1)
ANSEL (Register 7-2)
Analog-to-Digital
through
ANALOG-TO-DIGITAL
CONVERTER (A/D) MODULE
(PIC12F675 ONLY)
A/D Configuration and Operation
Analog voltages on any pin that is defined
as a digital input may cause the input
buffer to conduct excess current.
VOLTAGE REFERENCE
ANALOG PORT PINS
CHANNEL SELECTION
REF
GP1/AN1/V
is used. The VCFG bit (ADCON0<6>)
GP0/AN0
GP2/AN2
GP4/AN3
AN3.
REF
A/D BLOCK DIAGRAM
DD
is used, or an analog voltage
CHS1:CHS0
converter
The
V
CHS1:CHS0
REF
(A/D)
V
DD
GO/DONE
allows
VCFG =
VCFG =
bits
ADON
0
1
V
SS
ADC
circuit. The output of the sample and hold is connected
to the input of the converter. The converter generates a
binary result via successive approximation and stores
the result in a 10-bit register. The voltage reference
used in the conversion is software selectable to either
V
shows the block diagram of the A/D on the PIC12F675.
controls the voltage reference selection. If VCFG is set,
then the voltage on the V
otherwise, V
7.1.4
The A/D conversion cycle requires 11 T
of the conversion clock is software selectable via the
ADCS bits (ANSEL<6:4>). There are seven possible
clock options:
• F
• F
• F
• F
• F
• F
• F
For correct conversion, the A/D conversion clock
(1/T
1.6 s. Table 7-1 shows a few T
selected frequencies.
DD
OSC
OSC
OSC
OSC
OSC
OSC
RC
AD
or a voltage applied by the V
ADFM
) must be selected to ensure a minimum T
(dedicated internal RC oscillator)
/2
/4
/8
/16
/32
/64
ADRESH ADRESL
CONVERSION CLOCK
DD
PIC12F629/675
is the reference.
10
10
REF
pin is the reference;
AD
REF
DS41190G-page 43
calculations for
AD
pin. Figure 7-1
. The source
AD
of