PIC12F675T-I/SN Microchip Technology, PIC12F675T-I/SN Datasheet - Page 40

• Manufacturer Part Number: PIC12F675T-I/SN
• Description: IC MCU CMOS 1K FLASH W/AD 8-SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12F675T-I/SN

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Controller Family/series: PIC12
• No. Of I/o's: 6
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 64Byte
• Cpu Speed: 20MHz
• No. Of Timers: 2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Connectivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: PIC12F675-I/SNTR; PIC12F675-I/SNTR; PIC12F675T-I/SN; PIC12F675T-I/SNTR; Q1324216

PIC12F629/675
6.3
A simplified circuit for an analog input is shown in
Figure 6-3. Since the analog pins are connected to a
digital output, they have reverse biased diodes to V
and V
V
FIGURE 6-3:
6.4
The comparator output, COUT, is read through the
CMCON register. This bit is read-only. The comparator
output may also be directly output to the GP2 pin in
three of the eight possible modes, as shown in
Figure 6-2. When in one of these modes, the output on
GP2 is asynchronous to the internal clock. Figure 6-4
shows the comparator output block diagram.
FIGURE 6-4:
DS41190G-page 40
SS
and V
SS
. The analog input, therefore, must be between
Analog Input Connection
Considerations
Comparator Output
To GP2/T0CKI pin
DD
. If the input voltage deviates from this
VA
Legend:
To Data Bus
Rs < 10K
Set CMIF bit
ANALOG INPUT MODE
MODIFIED COMPARATOR OUTPUT BLOCK DIAGRAM
RD CMCON
A
IN
C
V
I
R
R
VA
LEAKAGE
T
PIN
IC
S
C
5 pF
PIN
= Input Capacitance
= Threshold Voltage
= Leakage Current at the pin due to Various Junctions
= Interconnect Resistance
= Source Impedance
= Analog Voltage
Q
Q
DD
V
DD
EN
EN
V
V
D
D
T
T
= 0.6V
= 0.6V
Reset
range by more than 0.6V in either direction, one of the
diodes is forward biased and a latch-up may occur. A
maximum
recommended for the analog sources. Any external
component connected to an analog input pin, such as
a capacitor or a Zener diode, should have very little
leakage current.
The TRISIO<2> bit functions as an output enable/
disable for the GP2 pin while the comparator is in an
Output mode.
RD CMCON
Note 1: When reading the GPIO register, all pins
2: Analog levels on any pin that is defined as
Leakage
±500 nA
Vss
configured as analog inputs will read as a
‘0’. Pins configured as digital inputs will
convert an analog input according to the
TTL input specification.
a digital input, may cause the input buffer
to consume more current than is
specified.
source
CINV
R
IC
impedance
 2010 Microchip Technology Inc.
CM2:CM0
GP0/CIN+
GP1/CIN-
CV
of
REF
10 k
is