PIC12F675T-I/SN Microchip Technology, PIC12F675T-I/SN Datasheet - Page 50

• Manufacturer Part Number: PIC12F675T-I/SN
• Description: IC MCU CMOS 1K FLASH W/AD 8-SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12F675T-I/SN

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Controller Family/series: PIC12
• No. Of I/o's: 6
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 64Byte
• Cpu Speed: 20MHz
• No. Of Timers: 2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Connectivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: PIC12F675-I/SNTR; PIC12F675-I/SNTR; PIC12F675T-I/SN; PIC12F675T-I/SNTR; Q1324216

PIC12F629/675
8.1
The EEADR register can address up to a maximum of
128 bytes of data EEPROM. Only seven of the eight
bits in the register (EEADR<6:0>) are required. The
MSb (bit 7) is ignored.
The upper bit should always be ‘0’ to remain upward
compatible with devices that have more data EEPROM
memory.
8.2
EECON1 is the control register with four low-order bits
physically implemented. The upper four bits are non-
implemented and read as ‘0’s.
Control bits RD and WR initiate read and write,
respectively. These bits cannot be cleared, only set, in
software. They are cleared in hardware at completion
REGISTER 8-3:
DS41190G-page 50
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-4
bit 3
bit 2
bit 1
bit 0
U-0
—
EEADR
EECON1 and EECON2 Registers
Unimplemented: Read as ‘0’
WRERR: EEPROM Error Flag bit
1 = A write operation is prematurely terminated (any MCLR Reset, any WDT Reset during normal
0 = The write operation completed
WREN: EEPROM Write Enable bit
1 = Allows write cycles
0 = Inhibits write to the data EEPROM
WR: Write Control bit
1 = Initiates a write cycle (The bit is cleared by hardware once write is complete. The WR bit can only
0 = Write cycle to the data EEPROM is complete
RD: Read Control bit
1 = Initiates an EEPROM read (Read takes one cycle. RD is cleared in hardware. The RD bit can only
0 = Does not initiate an EEPROM read
operation or BOD detect)
be set, not cleared, in software.)
be set, not cleared, in software).
U-0
—
EECON1: EEPROM CONTROL REGISTER (ADDRESS: 9Ch)
W = Writable bit
‘1’ = Bit is set
U-0
—
U-0
—
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
WRERR
R/W-x
of the read or write operation. The inability to clear the
WR bit in software prevents the accidental, premature
termination of a write operation.
The WREN bit, when set, will allow a write operation.
On power-up, the WREN bit is clear. The WRERR bit is
set when a write operation is interrupted by a MCLR
Reset, or a WDT Time-out Reset during normal
operation. In these situations, following Reset, the user
can check the WRERR bit, clear it, and rewrite the
location. The data and address will be cleared,
therefore, the EEDATA and EEADR registers will need
to be re-initialized.
Interrupt flag bit EEIF in the PIR1 register is set when
write is complete. This bit must be cleared in software.
EECON2 is not a physical register. Reading EECON2
will read all ‘0’s. The EECON2 register is used
exclusively in the data EEPROM write sequence.
WREN
R/W-0
 2010 Microchip Technology Inc.
x = Bit is unknown
R/S-0
WR
R/S-0
RD
bit 0