MCF5282CVM66 Freescale, MCF5282CVM66 Datasheet - Page 657

• Manufacturer Part Number: MCF5282CVM66
• Manufacturer: Freescale

Specifications of MCF5282CVM66

• Cpu Family: MCF528x
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 66MHz
• Interface Type: CAN/I2C/QSPI/UART
• Total Internal Ram Size: 64KB
• # I/os (max): 150
• Number Of Timers - General Purpose: 12
• Operating Supply Voltage (typ): 3.3V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 256
• Package Type: MA-BGA
• Program Memory Type: Flash
• Program Memory Size: 512KB
• Lead Free Status / RoHS Status: Compliant

complete before freeing the local bus for the debug module to perform its access. After the debug module
bus cycle, the processor reclaims the bus.
Breakpoint registers must be carefully configured in a development system if the processor is executing.
The debug module contains no hardware interlocks, so TDR should be disabled while breakpoint registers
are loaded, after which TDR can be written to define the exact trigger. This prevents spurious breakpoint
triggers.
Because there are no hardware interlocks in the debug unit, no BDM operations are allowed while the CPU
is writing the debug’s registers (DSCLK must be inactive).
Note that the debug module requires the use of the internal bus to perform BDM commands. In Revision
A, if the processor is executing a tight loop that is contained within a single aligned longword, the
processor may never grant the internal bus to the debug module, for example:
label1: nop
or
label2: bra.w label2
The processor grants the internal bus if these loops are forced across two longwords.
30.7
This section specifies the ColdFire processor and debug module’s generation of the processor status (PST)
and debug data (DDATA) output on an instruction basis. In general, the PST/DDATA output for an
instruction is defined as follows:
where the {...} definition is optional operand information defined by the setting of the CSR.
The CSR provides capabilities to display operands based on reference type (read, write, or both). A PST
value {0x8, 0x9, or 0xB} identifies the size and presence of valid data to follow on the DDATA output {1,
2, or 4 bytes}. Additionally, for certain change-of-flow branch instructions, CSR[BTB] provides the
capability to display the target instruction address on the DDATA output {2, 3, or 4 bytes} using a PST
value of {0x9, 0xA, or 0xB}.
30.7.1
Table 30-22
register. In this definition, the ‘y’ suffix generally denotes the source and ‘x’ denotes the destination
operand. For a given instruction, the optional operand data is displayed only for those effective addresses
referencing memory. The ‘DD’ nomenclature refers to the DDATA outputs.
Freescale Semiconductor
Instruction
addi.l
add.l
add.l
align4
bra.b label1
align4
Processor Status, DDATA Definition
User Instruction Set
shows the PST/DDATA specification for user-mode instructions. Rn represents any {Dn, An}
Operand Syntax
Table 30-22. PST/DDATA Specification for User-Mode Instructions
<ea>y,Rx
Dy,<ea>x
#imm,Dx
PST = 0x1, {PST = [0x89B], DDATA= operand}
PST = 0x1, {PST = 0xB, DD = source operand}
PST = 0x1, {PST = 0xB, DD = source}, {PST = 0xB, DD = destination}
PST = 0x1
PST/DDATA
Debug Support
30-39