ATTINY2313A-PU Atmel, ATTINY2313A-PU Datasheet - Page 196

• Manufacturer Part Number: ATTINY2313A-PU
• Description: IC MCU AVR 2K FLASH 20MHZ 20DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY2313A-PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 18
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• Controller Family/series: ATtiny
• No. Of I/o's: 18
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 128Byte
• Cpu Speed: 20MHz
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Notes:
21.3
196
T
Symbol
I
A
CC
= -40°C to 85°C, V
1. “Min” means the lowest value where the pin is guaranteed to be read as high.
2. “Max” means the highest value where the pin is guaranteed to be read as low.
3. Although each I/O port can sink more than the test conditions (20 mA at V
4. Although each I/O port can source more than the test conditions (20 mA at V
5. The RESET pin must tolerate high voltages when entering and operating in programming modes and, as a consequence,
6. These are test limits, which account for leakage currents of the test environment. Actual device leakage currents are lower.
7. Values using methods described in
8. BOD Disabled.
Speed Grades
ATtiny2313A/4313
conditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 60 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 60 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
has a weak drive strength as compared to regular I/O pins. See
0xFF), the external clock is selected (CKSEL = 0000), and there is no I/O drive.
Parameter
Power Supply Current
Power-down mode
CC
= 1.8V to 5.5V (unless otherwise noted) (Continued)
The maximum operating frequency of the device depends on V
relationship between maximum frequency and V
Figure 21-1. Maximum Frequency vs. V
Condition
Active 1MHz, V
Active 4MHz, V
Active 8MHz, V
Idle 1MHz, V
Idle 4MHz, V
Idle 8MHz, V
WDT enabled, V
WDT disabled, V
“Minimizing Power Consumption” on page
20 MHz
4 MHz
CC
CC
CC
CC
CC
CC
= 2V
= 3V
= 5V
CC
CC
1.8V
= 2V
= 3V
= 5V
= 3V
= 3V
(7)
(7)
(7)
(7)
(7)
(7)
(8)
(8)
CC
Figure 22-29
Min.
CC
CC
is linear in the region 1.8V < V
CC
= 5V, 10 mA at V
and
35. Power Reduction is enabled (PRR =
= 5V, 10 mA at V
< 0.15
Typ.
0.03
0.25
0.2
1.3
3.9
4.5V
Figure
1
4
CC.
22-30.
As shown in
CC
5.5V
CC
Max.
0.55
0.15
= 3V) under steady state
2.5
0.6
10
7
2
2
= 3V) under steady state
Figure
CC
8246A–AVR–11/09
< 4.5V.
Units
mA
mA
mA
mA
mA
mA
21-1, the
µA
µA